The reviews are automatic translation.
Milling by drilling machine
On 2015-01-05 21:12:15
Turning the X · Y Feed handle, can not smooth feed or become hard in the middle. We would like to raise the accuracy of the screw.
But I was going to use in precision work
On 2014-07-14 22:43:29
Is this only as have continued selling without any improvement over unpopular evaluation Why?
Bought well in Monotarou San does not understand the attitude!
Processing other accessories (aluminum case)
On 2012-08-11 17:49:39
It was terrible in the review because it is in other product shortage, I purchased this two-dimensional device (Paokku).
1. Play often in the slide portion. In particular, the Y-axis to change the handle is turned and the weight of the (lower), vice upper swing to the left or right. If you look closely, a screw to attach the diamond-shaped plate of the shaft through portion of the handle (M6 cheesy 100 yen shop type) is loose. Tightened place, the handle is extremely heavier operations difficult. After a plate of diamond is rotated 180 °, settlement the index of the huddle scale comes out.
2. Once disassembled, the drive shaft but box which receives (male screw) (female screw) is fitted to the base center, not parallel to the sliding portion. Box in parallel, to centering of the slide portion After the adjustment of the plate, became smooth. But heavy Sending a table as far as it will go.
3. Y-axis and the drive shaft is too pull it forward is out of the box (female screw). For not directly visible part, re-insertion difficult. Re-inserted the whole upside down. Should it do not come off.
4. Have been written as MADE IN CHINA is in a box, casting also miscellaneous, also processing miscellaneous. Screw or the like is also cheap. Price correspondingly less?
5. Use and does not adjust yourself difficult. Adjust also satisfied impossible to.
Milling in the drilling machine
On 2012-05-25 18:55:41
Play on the slide portion does not think many Japanese products. The slide portion contains one by one to each of the lower middle adapted to centered, but should be integrally molded. Also it is troublesome as Serve the core there is a backlash in the threaded portion to move to the front, rear, left and right. Niigata Seiki's did not expect to be such manufacturing.
There is no choice but to consent because the price the price, this is the best of the difficulty of the catalog Commercial Code, the user is no choice but to trust the manufacturer, this is a shame. Or the catalog Commercial Code is limited to the consumables?
I'm going to use is attached to the bench drilling machine. (No is to but still mounting use)
On 2011-05-08 15:02:49
I vice of this hand wanted to centering from before, but I thought those middle various expensive. Although I bought because it is exceptional value is not a heavy smooth upper side of the slide. Since the frequency of use is not even so much is ready to close their eyes at a price. Really good thing is a sample of what is decent price to.
Positioning of the drilling machine
On 2011-02-04 21:47:54
Movement can not be said to smooth. Backlash can not be said to be the absolutely no. However, no fatal defect missing if you use at the level of the hobby. It says the this price. If Nodea to use for professional work, you should buy things decent price.
Was a plan to use in the drilling machine.
On 2011-01-25 13:17:26
While other people review of it was terrible, there is no similar things, because the price was affordable purchase.
I went immediately operation check arrived the other day, but it was reviewed as terrible to make.
But it turned the slide part is the liver of this product by the handle there is an irregularity in the movement. So it is turning like a bent screw. Even Yeah slide part in the meantime no longer move even with the living. Casting part After turning a little focus is broken and Boki'.
Oil in the cross-sectional half position when you see the cracked cross section was steeped.
It seems to have been cracked by brute force assembled the stage at the stage assembled to guess. So far it has been variously using the made in China had never seen the terrible things up to this point. I think as a level of product that it is below the level of the Chinese products.
Without notice to the bowl that was like cracked, holding a ... like a feeling that crack When you try to use.
Mainly the currently drilling
On 2011-01-08 22:23:58
First of all the terrible state of the bolts being used.
Female screw has not been cut well.
Parts of the accuracy of memory is terrible, because it was distorted even surface of the parts have memory is a shift
Movement when moving the vice base has come out bad parts.
It could be improved if you own the above-mentioned part.
Not recommended if you want to use without stress.
I think that you want to use in the drilling work. I bought it.
On 2010-07-26 23:23:26
I was looking at this thing in the do-it-yourself store. It was about ¥ 7000. Indeed, the precision work, but we recommend the people of other products,
The minute to adjust your own, is sufficient. I bought I think the material cost.
On 2010-06-11 13:47:36
Such as screw tightening and adjustment, I did not decent to be able to assemble, but you can use by adjusting it on your own.