The reviews are automatic translation.
... To secure the small processing
On 2016-06-05 15:07:04
When the plastic resin and wood processing, but did not notice until now because it was with a non-slip plastic in the mouth of the place ,,,
If you think trying to fix and remove the slip of plastic in order to sandwich the metal, have the mouth of the person running is skewed, it does not take the pressure only to the top of the metal to be processed.
Mouth of the fixed portion, which surface to sandwich the top has become almost a right angle, towards the mouth of the movable portion is not at an angle of about 80 degrees, it will tilted absolutely sandwiched metal.
In addition, the difference is also the mouth of the thickness.
But tested seal had been put, is disappointed.
Rotation split processing in the drilling machine and milling machines
On 2016-03-17 21:03:30
It is the purchase of reading the reviews, but the evaluation is not so good. (Color ...)
Price will feel only to be reckless to ask the price, but I thought that very easy to use if it has rotation angle memory.
Will may I mean, even in 360-degree protractor but, MonotaRO handling goods is too large so diameter Φ90mm.
If you have a 360-degree protractor of diameter Φ65mm, interleaving a rotating platform of clearance, but ...
Product images are two-tone color of blue and red, but, but that paint color is changed is I think is that there is no way, the color of the Received items such as Brad metallic, mixed with metallic pearl to darker really blood than red It was a color like.
Whole is starting to flicker eyes Since Brad metallic, it is difficult to very easy to use.
If you change the paint color, I wanted in the color of blue or green system.
At the time of purchase, but the fixing holes in the representative image I thought two or four Kana, was a half-hearted that three is a negative evaluation.
The dimensions of the fixing holes in it, diagonal hole the dimensions of the next in 74mm was a half-hearted dimension called 54mm and 56mm.
Fixing holes I think can be fixed in a 6.5mm so M6 or 1/4 inch screw, but, if you do not clean with a drill of 6.5 ~ 7.0mm because the shape of the hole is distorted, the screw is not passed,.
Before the entire painting, the protruding portion exiting in creating casting I wanted you to scraping.
When cutting the projection part after painting, so would take to paint, I want to sell the repair paint cheap (just as good).
At the same, there is after the hit 10 locations close to the after painting. I think that there is no problem to use, but you suspect the merchandise management.
And, also a former box is removing the cushioning material, But what does minded to say the people of the box from the commodity is small? ?
Also to devise how to put, as the maximum 10mm lower height (small) is a box.
Good point, for the precision calibration products on their own at a price Nari products, is looking forward to the point.
Or price to precision vice is how much, I look forward to.
__ / __ / __ / __ / __ / __ / __ / __ / __ / __ / __ / __ / __ / __ / __ / __ / __ / __ / __ / __ / __ /
Ever review opinion to the:
> Fall because with a cover of plastic has not been fixed
There Innovation but, soldered-brazed useless because the length thing that for anyone to be, I think it is better that have not been fixed, such as with a bond.
It was he, the Purakaba is not there to vice is, I want you to recreate! !
> Is anxious hardness of a little feed screw
> Will be on the structure, but in the work to do a number can not be rotated with one finger, inefficient
> Must not lightly be pointing to the heavy oil also rotation of the lever.
> Gap (backlash) is large and not to adjust the bolt of the base of the axis of rotation.
> The bottom of the pedestal is the slope and because it does not come out the horizontal, mounted to the base of the metal.
Whether they are purchased know, I do not know whether they are impulse buying, it is unjustified resentment if you look from me! !
Certainly hard and heavy and I say I say, the external thread and the internal thread of clearance It is almost no state.
If you want to lighten the really tightening the screws, I think that may be Tatenaose the tap into the internal thread side.
(Although I think that it is probably inch screw)
Those of the rotary table should the like rattling can be reduced considerably if the horizontal milling to decompose once. It pops up at No. 13 wrench.
To completely eliminate the rattling, it carved a groove to put the bearing balls, if Kuminaose the bearing balls 15 to 20 about put, rotating platform should be fairly stable.
The milling and grooving processing, but might take a few thousand yen, it will say that asking for it only plans.
It is not in the system determined by the thousand yen.
Even just to flatten the unevenness in the sand paper from 1000 to 3000, I feel that the movement is smooth.
This product is, I think that can be seen if you look at the image, but it is rotating vice of the casting mold.
If would like to precise rotation vice in the true sense of the term, you should buy a thing of type out shaving.
(All the moving parts those were milling after casting)
Such as https://www.monotaro.com/g/00143696/, these products ...
To 1 thousand yen of goods, I think that is wrong those seeking tens of thousands of yen level of performance.
However, since I think that the point that category had become "precision vice" there is a fault in MonotaRO side, we put out a request for revision,
Currently, no longer a category referred to as a "precision vice".
On 2016-03-10 17:04:18
Noodles of the fixed part is bad, because although with a cover of plastic has not been fixed fall,
Fixing things and then replace it with the one that can be adhesion of the rubber was getting better.
Cheap is good, I think, but blame new ... movement is hard but ....
It was so-so shopping From a price.
For chamfering work of small parts
On 2015-12-15 15:08:34
Range that can be N bitten because although anxious hardness of a little feed screw tightening less frequently. I think the price accordingly.
Retention of small parts, fixed
On 2015-05-23 15:44:37
Seems severe criticism in other reviews, but I in easy-to-use desktop've been using a more inexpensive type, fully satisfied with this. If you want more accuracy, should you buy a higher things.
Soldering of the work fixing
On 2015-05-22 13:42:18
Force to close open in the vice of functionality is required, because of it, but had you returned or exchanged was therefore accounted for acceleration and to fix the work do not know was the same, it takes even return of labor, was discarded.
It makes similar only all forms, as the vice is not available basically.
Fixed at the time of soldering
On 2014-08-10 15:08:04
What I precision ...?
Idea that may be cheaper, the worst of the reputation
Not only the manufacturer, also here that sells guilty
Handle is heavy (heavier and grease-up)
But it will be on the structure, in the work that do a number can not be rotated with one finger, inefficient
Also trouble in the disposal as it is disposable sense I use once
In addition, their own to reflect on that had a penny-wise and pound-foolish
I want you to deal with only products more reliable because mail order
We decided to put out to the bazaar without
Bending, drilling, soldering of thin iron plate
On 2013-04-18 23:54:47
If you do not adjust the bolt of the base of the rotating shaft gap (backlash) is large. Loosening of the bolt is also necessary. Sweet the accuracy of the slide portion of the back side of the jaw, is to tighten rattle.
On 2013-02-03 18:40:41
There is a precision device, but it is not precision.
It does not lightly be pointing to the heavy oil also rotation of the lever.
Fall down and not wearing a seat you want.
The lure production, did not work.
Made from photographs, it is sweet.
Machining of small parts
On 2010-09-03 17:17:40
In name only a "precision", this does not work. Handle firmly, engagement or worse, does not change also refers to the lubricating oil. The bottom of the pedestal to the bonus is the slope and because it does not come out the horizontal, mounted to the base of the metal. Bad bite there is in all parts, this is a problem as a product.