The reviews are automatic translation.
Customizing the cross bike was bought in new car
On 2016-09-11 01:27:06
When installing, it takes a very long time in the fitting. As it was to other people reviews, the cutting of stainless stay is required preparation of robust tool. It is acceptable for general-purpose products. We were able to very clean finish by multiplying the time to the fitting.
Impact resistance of a body material, can be evaluated as a commodity that has been well thought mounting stay, etc. to absorb the impact.
Since the two bodies at packing overlap directly, is sorry had with a myriad of small abrasion to the overlapping portions.
Is is because the problem solved by just pinching a piece such as cushioning material in between, I hope to improve.
It was attached as a fender of 700X38.
On 2016-02-09 12:03:02
It was also be mounted by a thick tires 700X38.
There is no room in the side part, but it can be used without any problem without any interference with the tire to be mounted on a little bend the wire portion.
Cut the wire, you need a tool that was as chitin that other person is said.
I think that sufficient performance as a generic product.
To the purchase for repair and replacement of nearly 10 years elapsed cross bike
On 2015-10-27 12:55:24
Is also good, we have status quo very pleased durable likely Note and design on very light.
It was attached to a 700 35C bicycle, but the width was not a problem because there is about 4.5cm.
Since neat manual also comes with, you can also install with confidence.
Installation work itself is very easy to be completed in 5 to 10 minutes position.
The purchaser in accordance with the size of the bike to possession
Without a cut of the V-type stay in the only points not I think the biggest difficulty.
Stay is the first impossible if there is no very thick and of something tool.
In bare hands I think I even difficult to bending.
Because it was in possession of a saw (of about 800 yen) for the metal Fortunately
So the order to take the plunge this time it would be probably okay.
Cut to the prospectus as was successfully done.
But it took a 5-minute position per one because there are quite thick.
A total of eight of the cut was quite tired. I think a fine effort.
But is highly recommended can trade if for those where there is the likelihood of some sort of tool
Even if slightly higher amount of money who do not have confidence that also without cutting tool
I think it safe is better to chose the other product.
If you want to purchase a tool for the cut, since become quite a amount of money in total.
And simplicity of price, quality, and mounting, none but I think that it was good to buy nice
If you and could not be cut, it would have been as between opposite ones evaluation.
For your bicycle repair
On 2015-10-05 23:57:14
I understand that white cut a portion of the spokes on your own, you can not stick cut of this hard stainless steel.
Eventually after using only the rear of the bracket it was as it becomes garbage.
For attachment to a cross bike.
On 2015-02-11 20:03:23
Because it does not only look at net photo, there was a variety of anxiety, but I bought a look at the price. I expected what delicate look at the only price, but was surprised to have been firm. If you this at this price can get, fender for the 700c is Will not no other choice.
27 repair of inch City cycle
On 2014-10-28 05:29:38
Because for the 700C it was anxiety, but could also be without mounting problem 27-inch wheel. However, in a vehicle with no tab to the front and rear of the end, because we fixed the stay to the hub bolts, took time to processing of the stay. Although the rear wheels was also just good length of the stay, the front wheels needed a cut about 2cm.
Since the width is fine, I think that does not suit the load of the thin tires. Be perfect if much of the city cross-32C.
On 2014-07-17 19:21:35
Since the polycarbonate and stainless steel, it may be without rust lightly.
Attached to a road racer
On 2014-02-02 21:03:17
I thought attempt to install the road racer, but it does not have much margin in the original between the frame and the tires did not work as it is to interfere both the front and rear. Since Fortunately fender body is made of polycarbonate, the back side is shaved the caliper part and the part close to the bottom bracket of the brake, was able mounting somehow cutting the parts to be fixed to the brake part. Since the front side is absolutely fender and plug the fender in the gap of the tire and the front fork may interfere with the tire, cut the front half, it was fixed to the front fork only half behind with a cable tie. Metal wire is if you have a wire clipper, you can easily cut. Because the thing-in-itself was good-looking than expected, it is recommended if someone in the frame.
On 2014-01-24 02:11:30
Purchase for commuter 700C bicycle fender was damaged.
I also like a good after installation.
As stay everyone is written it must be cut long enough to 3cm.
But I was looking for a wire cutter in the do-it-yourself store, because you can not find the good stuff,
To buy gold saw it was mounted off the tip burr in the cut and rasp.
It is not a less bitter, but those tools work is weak might be struggling.
Since the off-the-shelf goods, but it seems to be a longer as attached to the various vehicle,
I think that may be attached to a little more simple.
Peugeot City cycle
On 2013-12-12 23:37:22
This should not be bought is amateur.
Do not turn off is very wire in the cutting tool that and household pliers "eating outright".
I was able to cut finally borrowed a "wire Clipper" from acquaintance.
If you are selling for the 700C, it is funny tire size determine the cutting to the purchaser because I constant. But is convinced if fit with a screw to about fine-tuning.
At the very least ,,, Toka concave cutting are marked in 1cm increments
Although Well amount of money is the hope that it will be unavoidable because the amounts