The reviews are automatic translation.
On 2017-05-25 17:24:59
On 2017-05-08 18:06:13
The plastic of the base part was broken. I think that feeling of use is no problem. Without the above, I am satisfied
We used to oil exchange of the diesel engine.
On 2017-04-02 07:28:53
Although I used to oil exchange of the diesel engine, also drew the pump more than 100 times to pump up for the nozzle of the hose is fine took two hours, I want you to many types of hose.
Automotive Oil Change
On 2017-04-01 16:18:42
But it lost the same amount goods of manual purchase a simple likely here.
Since the car is is Hiace does not reach at all the length of only 6mm hose
Extended with 6mm hose to the tip pointing to the body of the 10mm ahead.
Inserted to the oil pan bottom with the feeling of pushing a little. Immediately seen from hitting the Kotsun.
Conversely, it may be did not enter the hose and soft as far as it will go.
Immediately pull start with a few degrees of the piston, make a but drips and sound but slowly
Suction start. Because I stopped When you release the little eye also piston start.
Is defined amount also knew but finish since last began suction along with the air
It was found immediately. Stick even approximate idea in scale.
6mm hose and 10mm hose and connection port was worried about leakage because there was in the car but was Tsu without any problem.
Be but look forward to the future of durability was a good shopping as DIY school because when not to change elements This can be enough oil exchange.
When oil exchange of marine engines
On 2017-01-11 17:46:03
Not limited to the automobile, there is a feeling that has now become a staple in the engine of the ship.
Business trip maintenance
On 2016-12-08 09:06:26
We were previously using a third of the commodity, but I tried to use to purchase as it was no longer take the pressure.
You can use without a problem, but after is durable is whether.
When the vehicle maintenance
On 2016-05-26 17:33:48
Dirt not, you can work quickly.
Oil change of motor vehicles
On 2016-05-07 18:10:12
Purchased last year, is the impression of try to use 9 months.
When the main body of the hose (thicker) is too hard pull reach you do so until the oil pan, it will exit from the rubber joint. Contour 14mm As a countermeasure, replace the oil hose with an inner diameter of 10mm, and are used to have a flexibility. Ahead of 6mm of the hose is intact.
I have a breath of only a few air from the joint portion of the rubber, but it is as it is for the time being. I think that I might Mako even tape Once you become a little more seriously.
Is the storage of the hose, but it is a little inconvenient because the cylinder of the housing so that people of the former is written is short.
Or with respect to the suction capacity, it would be ten minutes you do not know the exact time, but ordinary car (about 4-5 liters). However, to warm-up for about five minutes before withdrawal has to soften the oil. It takes more time than the pull out from the bottom, it is easy to think of dive down to jack up. However, if you also exchange oil filter, oil change and jack up without this changer.
Since the hole in the street level gauge that is also described in the notice does not enter 6mm following the Wagon R (MH23S · K6A engine) could not be used. Because after Honda ACTY Vamos also of the level gauge pipe per is up and out from the side of the oil pan, completely did not completely suck. Other car seems not so far problem.
I think that it was good to buy and think in total.
On 2016-03-31 02:41:58
Although air changer in turn broken in three months I tried to manually easy to use.
Used to - (G, etc. Suma) under unplug the drain with no car
On 2016-03-28 12:55:30
It is a commodity of just problems. Nylon Ju - you must be careful upon joint is loosely used between the parts and body. Upward ho - scan is not out does not reach to the EG. It will lock in or pumping because tilting the body. It is very tricky product to use in front of the customers. Previous other E - force - used a few years similar such things, but there was willing to work as expected. It should not be sorry.