The reviews are automatic translation.
Car of damping, soundproof
On 2016-07-12 08:56:51
Use in vibration control and soundproofing Raggeji. It was applied at a thickness of 2mm to the iron plate. Work because the glue is also good thirst also reasonably fast is easy. Nothing end without a problem because the type to paint with a brush, brush will be clean in the wash. I do not feel is a dramatic change, but I think that it is good as a dump agent.
Soundproof in the tire house of private cars, ... to prevent such as stepping stone
On 2016-06-27 23:18:08
Since the brush was also bought Apply hand Good luck!
Automobile door deadning
On 2016-03-28 18:48:06
Used for audio door deadning of automobile. Painted or to those of the material, such as the inner paste inside chunky hard paper, deadning sheet Hari hard outer panel, used in reinforcement iron plate portion. Vibration-damping properties over a period of 10 days even after curing hard and will continue to UP. Ideal will be realized in the proper use of the deadning sheet Hari easy part. Since the inner bonding resin portion so as not to contact you think that we need some sort of primer, but did not need to be applied to it.
Sound insulation of car
On 2015-12-07 19:41:07
It applied to the entire inner surface of the floor panel. It is a little consolidated whether it is the influence of the temperature (feeling like a putty mixed sand) Because it is water-soluble, it gets softer when adding a little water. (However, because thick coating is difficult, viscosity adjustment is carefully done.) The curing time (in the instruction manual) at the time of overcoating is 3 hours, but discoloration indicative of hardening at 2 to 30 minutes even at the temperature of 15 ℃ From blue to ivory) was seen, and it was possible to coat repeatedly. It took 3 hours to dry the tactile touch, and restoration of the floor mat was also possible. After 12 hours it is completely dry (hardened) and workability is very good. With this amount, a coating film about 2 mm thick could be applied to 4 m2. If you think that the tire house is sufficient enough with this one, if you expect further effects (if you are going to thicken it) I think that 2 is the proper amount. Although it is not measured by the numerical value, clearly there was the effect as expected. By the way, it can easily be washed away with water if it is completely cured.
Sound insulation inside the tire house
On 2015-10-18 18:08:35
As we used one tire house, the rainy day became much more quiet. Because it is beige color, it may have gotten quiet unnecessarily as it blew a black silent spray of Eamon after drying.
Car deadening work
On 2015-10-02 20:35:59
Although it will be used continuously for a long time, it has considerable soundproofing effect by applying it under the floor (outside) of the car. Synergistic effect can be expected by sandwich construction inside. (It is not double that saying.) Generally, when traveling in the rain, is it feeling that driving noise is quite low? It is not that sound completely disappears or it is not that the noise decreases significantly, but it feels quite quiet. Just ... once it got used to it. The drawback is whether the paint is difficult with a brush. It was a good feeling to paint with spatula or gloves.
Countermeasure against running noise of car
On 2014-10-20 21:59:13
Because soft butyl can not suppress low frequency, physiologically unpleasant muffled sound tends to be emphasized. Damping steel plate is effective, but it becomes heavy when sticking on the whole surface. If you hate to become heavier and disperse and attach small pieces of vibration damping steel plate, it is difficult to suppress the entire band evenly because the split vibration mode changes. In that respect, the coating / curing type Knoxdor reduced the total amount without complicating split vibration. Compared to other damping materials, the attenuation band is wide, so it is the greatest merit that it is difficult to produce habit or disgust. Therefore, it is also suitable for large resin parts with large area that easily split vibrations. Although the adhesive of the vibration damping steel plate deteriorates over time, it is one of the features that does not need such worry. The disadvantage is that it is inevitable to increase the weight correspondingly because it coats a wide area even if it is thinly applied. If you ignore the sound quality and effectively lower the sound pressure of running noise, it is a vibration control steel plate, but if you do not want to impair the original sound quality, the coating / curing type is a good choice.
Car quiet up
On 2014-08-02 17:53:17
I bought it after examining at various sites, but cost performance is enough. It was constructed on the plastic inside the tire house of the minicar's front wheel, but the road noise was reduced enough to make it realistic. I used it for overprinting, so I used it about half, but this time I am thinking to use it for the floor under the seat. This product was the cheapest for monotaro but I'm curious that the date arrived was late.