NoteBuy more than* S$150* and get FREE SHIPPING

  • Silicone Rubber Sheet

Silicone Rubber Sheet K-125(50)

4.47 (19)
Package Qty.
Ship pack of
11.08 SGD
In stock
Now we ship to...
...see all
Item Feature
Oil Registance
35(150deg Cx70h)
Cutting Time Elongation (%)
Tensile Strength (MPa)
JIS Standard
Silicon hardness 50
Milky white
Width (mm)
Heat Resistant
225deg Cx70h when hardness change (type A durometer): tensile strength change +2 (%): -14 cutting Shin rate of change (%): -16
Compression Set (%)
12 (175deg Cx22h)
Hardness (Durometer A)
Specific Gravity
Rubber sheet
Heat-Resistant Temperature (deg C)
-30 - +150
Thickness (mm)
Length (mm)
Customer Reviews
5 star 11
4 star 6
3 star 2
2 star 0
1 star 0
Review Rating: 4.47
19 Customer Reviews
The reviews are automatic translation.
The spacer of the clamp to be attached to the bicycle
From Japan
On 2016-07-09 08:56:56
Than the minimum diameter of the clamp to attach the accessory to the bike, there is that the frame is fine, but do I have to adjust the thickness is wound around a resin sheet, there in the hardware store only propylene rubber or natural rubber, immediately since deteriorated cracked, If you are looking for variety, we found here and fluorine rubber. More of silicone chose at that would be difficult to compromise the aesthetics translucent. It was very helpful to buy a smaller size.
This review is about item#07057845.
It used to underlay when many things make the handiwork in the glue gun
From Japan
On 2016-07-01 17:31:22
A low-temperature and high-temperature glue gun, depending on the application has been used in high frequency, but sag and leak unexpected is the problem. Not quite take and drip to those poor, also it is the worst useless. By performing the work covered with this sheet, and can be easily recovered after solidified also also leak dripping, since there is no contamination of impurities, in the glue, when such as to fill the large type what was moderately crushed the It will also be savings of glue by putting.
This review is about item#07057976.
Plastic tank cap water stop packing the creation of (for water)
From Japan
On 2016-04-30 17:44:54
A good product, we are satisfied with early arrival to the product. I think that if Negaere a cut in processing size if possible.
This review is about item#07057924.
From Japan
On 2015-07-30 00:33:17
Just a good size, price is also good at Single Use cheap
This review is about item#07057845.
Seismic isolation
From Japan
On 2015-07-27 21:43:02
Nicely it was good to go
This review is about item#07057994.
When the paint, used for masking purpose in a place that should not be takes paint
From Japan
On 2015-06-02 15:10:15
It does very good. And choose various thickness, it can be cut to the size you like. In the future, it is to buy.
This review is about item#07057933.
Use as a hobby
From Japan
On 2015-03-04 16:09:52
So I was looking for a silicon rubber sheet Just was a reasonable size and price.
This review is about item#07057924.
Insulating sheet of electrolytic corrosion prevention
From Japan
On 2014-10-31 15:32:21
With water around, you use in a location that SUS and aluminum are brought into contact with each other. If the adhesive is required, stick strongly prefer the Basukoku a filler than a silicone-based adhesive.
This review is about item#07057906.
Used at the time of plastic molding
From Japan
On 2014-09-02 15:29:20
Since the unexpectedly extended, it was easy to use and fit into a mold. If there is more what the thickness is thin, I want to try.
This review is about item#07058116.
Protection of the inner wall
From Japan
On 2014-08-06 09:50:38
Product, I was good in as expected, some had turned yellow and have sunburn. Since never cheap is not a commodity, such as those discolored wanted it will be taken into consideration.
This review is about item#07058073.