Buy more than* S$200* and get FREE SHIPPING

  • Electronic Counter Timer H8GN
  • Electronic Counter Timer H8GN
  • Electronic Counter Timer H8GN

Electronic Counter Timer H8GN H8GN-AD-FLK

Package Qty.
Ship pack of
*[No return] You cannot return this product. For details, see FAQ.
359.90 SGD
Shipped after 2017-04-06
Now we ship to...
...see all
Item Feature
This product is manufactured in Japanese standards. Please check the specification before you order.
Allowable Voltage Range
85-110% of the supply voltage
Reset Method
(Timer A, B, D, E, Z mode) external reset, manual reset, automatic reset
Power Supply Voltage (V)
Synchronization Mode
Insulation Resistance (Mohm)
More than 100 (at DC500V mega)
Connection Method
External: Screw terminal (M3 screw)
Case Color
Smoke gray (N1.5 (black only the front part))
Display Type
(H, min, s), CMW, OUT, RST, TOTAL 7 segment negative LCD, time table shows
Number of Digits
(Calculated value, preset value significant suppression system) can be preset up to a maximum of four digits
Power Consumption
(: Inrush current less than 15A DC However maximum load) 1.5W or less
Input Signal
Counter function time: CP1, CP2, reset timer function time: start, gate, reset
Withstand Voltage
And output 50 / 60Hz 1min communication terminal AC1500V: conductive terminals with the exception of the output with 50 / 60Hz 1min output terminal AC510V: non-charging metal part between the conductive pins other than the 50 / 60Hz 1min output AC1500V: non-charging metal part between the output terminal conductive terminals except: AC500V 50 / 60Hz 1min non-continuous contacts between: AC1000V 50 / 60Hz 1min
Control Output
(P level, reference value) (cosphi = 1) DC30V 3A minimum applicable load DC5V 10mA 1c AC250V 3A resistive load: contact output type
EMC Standard
EMI: EN61326 radiated disturbance field strength: EN55011 Group1 class AEMS: EN61326 Electrostatic Discharge Immunity: EN61000-4-2 electromagnetic field immunity: EN61000-4-3 conductivity noise immunity: EN61000-4-6 burst noise immunity: EN61000-4- 4 surg
Protection Structure
Front operation section: NEMA4X for indoor use (IP66 equivalent) rear case: IP20 terminal area: IP20 + finger protection (VDE0106 / Part100)
Input Method
Below 2V, impedance when opened :: 100kohm or less maximum applied voltage short circuit residual voltage (about 2mA current outflow during 0ohm) 1kohm following: input impedance short time due to a short-circuit of open contact: No-voltage input: DC30Vma
Storage Temperature Range (degree c)
(No freezing No condensation) -25 to +65
Impact Resistance (Malfunction)
3 times for each 100m / s 2 6 direction
Maximum Counting Speed
In the case of 1 times other than 30Hz / 5kHz pre-scale, maximum counting speed of setting up the 5kHz will be about one-half. Moreover, it will be about half also If you choose addition or subtraction mode.
Vibration Resistance
Number 10 to 55Hz single amplitude 0.75mm 3 each direction 2h vibration
Count Range
-999 to 9999
Memory: EEP-ROM (non-volatile memory) (100 000 times the number of writing)
Ambient Humidity
25 to 85%
Waterproof packing
Weight (g)
Communication Method
RS-485 (2-wire half-duplex)
Mechanical: electrical 10 million or more times: 100,000 times or more (AC250V 3A resistive load)
Operating Ambient Temperature (deg C)
(No freezing No condensation) -10 to +55
Power Reset
Minimum supply opening time 0.5s
Display Mode
Adding (UP) table view, subtraction (DOWN) Table shows
Communication Function
Transmission line connection: multi-drop Communication speed: 1200, 2400, 4800, 9600 bit / s Transmission code: ASCII data length: 7 or 8 bits stop bit length: 1, 2 communication buffer: None: 40 bytes retry function : None bit error detection: (none, eve
Sensor Waiting Time
(The sensor during latency, does not accept the input of the control output is OFF) 260ms or less
Noise Immunity
The square-wave noise by +/- 600V noise simulator: operation between power terminals: +/- 480V between the input terminals
Output Mode
Counter: N, F, C, K Timer: A, B, D, E, F, Z
Character Height (mm)
(Red), setting 7: 3.4 (green) the current value
Safety Standards
C22.2 No.14 EN61010-1 (IEC61010-1) UL508 CSA: VDE0106 Part100 fit (EN61326) II EMC standard 2 / Overvoltage category Pollution degree (finger protection provisions)
Input: Input addition, subtraction input, discrete input, the phase difference between the input
Start, reset, gate: Minimum input signal width 1ms / 20ms (switching)
Impact Resistance
3 times for each 300m / s 2 6 direction
Vibration Resistance (malfunction)
Number 10 to 55Hz single amplitude 0.35mm 3 each direction 10min vibration