Customer Reviews of Forged Tap Wrench
The reviews are automatic translation.
Showing 1 - 20 of 20 Reviews
When subtotal tapping
On 2017-06-05 20:31:04
Especially it can be used without problems. I think that cost performance is a good product.
It is used for repair etc.
On 2017-04-11 11:28:41
It was nice to buy it very easy to use. It is amazing.
Overhaul of fuel cock
On 2017-02-21 22:42:06
Although it was genuine replacement for every cock, I bought the caulking caulking with a drill, scooped it with a drill, exchanged an o-ring in the inside, I had to tap to fix the cover, I bought it. I do not have to turn it with Vice Grip now.
Shuffle the tap of the bicycle pedal
On 2016-11-01 14:29:10
It was able to be used without problems with 9/16 inch · tap.
This review is about item#7333821.
Do not do that
On 2016-10-12 17:47:07
It gets loosened soon and does not become usable.
As a handle like a tap.
On 2016-09-29 16:49:24
It is very helpful at cost. I do not know that durability will not be used.
6mm, 8mm tapping
On 2016-07-06 19:09:52
The tapping shank tightening pitch is coarse and loosened with tapping off for 2 to 3 times and rattling, which increases the work of tightening the handle every time.
For hand tapping work.
On 2016-05-08 17:09:11
Machining of machine parts
On 2014-11-09 19:35:52
I think that it can be used sufficiently.
Threaded handle with tap
On 2014-10-20 15:54:03
I felt the durability is also easy to use because it is large in size
On 2014-01-24 11:40:08
The M20 tapped screw was troubled and the aluminum part broke during work. I think that it can be said that it is perfectly insufficient to break up in the work of clarification.
Female thread cutting
On 2013-08-17 17:34:58
Since it is made so that the concave side does not move, I am concerned that the center of rotation is shifted (eccentric) from the center of the handle.If that other products are movable, that person is more likely to work I do not think there was something like having to tighten the tap over and over again, as it was only 3 tap work, it is not possible and not possible.
Processing to metal
On 2013-01-06 01:28:20
The nails will bend. The rattling coming out and becoming easier to loosen It is recommended to buy a solid one with a tap handle broken or entering diagonally is a waste
On 2012-05-08 07:37:51
I used it for M8 tap stand. When tapping about ten, the central mouthpiece was deformed. Even if quenching is not in, deformation may be influenced, but even if the handle is tightened, the central mouthpieces first contacted and did not hold the tap. It was written to be usable with M6 or higher, but is it okay?
To make the shaft mounting hole of the golf club the specified size.
On 2012-05-01 12:39:39
It can be used normally. I am not used to it yet so I do not know the power of desorption (reamer), but I think that you can use it properly if you get used to it.
Tapping and reminder work
On 2012-03-06 10:56:09
Although it was meant to correspond to M12, I could not get a shank of straight reminder of M12.
On 2011-11-14 19:19:24
I use it normally. There is no particular problem. Because use frequency is not so high it thinks that it is a bargain for a cheap price.
Used for Saraje processing of tapered screws (PT 1/4 to 3/8) and metric screws (M16 to 20) taps
On 2011-09-28 09:43:32
Although I bought M6 - M20, the center die - cast part was broken in over 1 month 's use. I think that it is typical of low-end vampire. I bought and regretted. You should not purchase if you expect a little durability.
When processing and repairing motorcycle parts
On 2011-01-31 14:12:23
Previously, the tap handle that was included when purchasing an inch size tap set was purchased as a substitute because the holder part was broken by several times use, but it was the same thing .... This is also short-lived. As a feeling of use, the play is much easier to loosen. Is it reasonable for the price?
Used to stand pipe female thread
On 2010-12-13 22:17:08
It's good because it's small and it's small. However, cautiousness is also important
This review is about item#09215936.
Customers Who Viewed This Item Also Bought
59.63 - 66.09 SGD
80.19 - 82.77 SGD
62.76 - 129.90 SGD