Mechanical / Structural Components
Other Related Pages
- NOK O-Ring P Series (for Dynamic)An O-ring is an annular packing with an O-shaped (circular) cross section, which is generally mounted in a groove and compressed appropriately to be used as a seal for a wide variety of fluids such as oil, water, air, and gas.Type For dynamic (P type) Material NBR-70-1 (type 1 A) NBR Nitrile Rubber Hardness 70(±5)° Withstand Pressure (MPa) 7 Heat Resistance Temperature (℃) 100
- Mitsuboshi Belting V Belt Type B (Standard)It is a set-free belt that does not stretch or shrink over time during use and is suitable for multiple hangings, and can be expected to have a long belt life. In addition, it is easy to obtain by handling it as a standard V-belt.Type V-belt Operating Temperature Range (℃) -40~+70 Offset Angle (°) 40 Electrical Resistance Value 50MΩ or more Material (Belt) Rubber Belt Shape B
- NOK O-Ring S Type for Static (NBR)An O-ring is an annular packing with an O-shaped (circular) cross section, which is generally mounted in a groove and compressed appropriately to be used as a seal for a wide variety of fluids such as oil, water, air, and gas.Type For fixing S type Material NBR (Nitrile Rubber) Hardness 70(±5)° Heat Resistance Temperature (℃) 100
- MonotaRO V belt A type standardA conductive V-belt that can be widely used in general industrial machinery. For conduction belts. * Please do not use it for any other purpose.Material Rubber Tensile Strength (kN) 4.4 Elongation(%) 3
- MASUOKA O-Ring P (For Dynamic, For Static) Fluoro RubberHas heat resistance and chemical resistance. Packing that requires heat resistance, oil resistance, and chemical resistance, corrosion resistant packing in chemical factories, gaskets, diaphragms, tank linings, hoses, pump parts, etc.Specification Heat and chemical resistant Material JIS B 2401 Type 4 D (Fluoro rubber) Hardness 70 Withstand Pressure (MPa) 7 Heat Resistance Temperature (℃) 200 RoHS directive (corresponding to 10 substances) Correspondence
- NTN Miniature Ball Bearing / Small Diameter Ball Bearing ZZ (Standard Type) (No Flange)Miniature ball bearings have a nominal bearing outer diameter of D <9 mm, small diameter ball bearings have a nominal bearing inner diameter of d <10 mm, and nominal bearing outer diameter D ≥ 9 mm. There are metric type and inch type. Most commonly used seal-shield bearings have a width of... Read MoreMaterial (Main Unit) High carbon chromium bearing steel Flange Without flange JIS Grade 0 Shield Shape Shielded on both sides Load Direction Radial Outer Ring Type Flat Race Ring Shape Deep groove ball bearings Number of Track Trains Single row Rolling Element Material High carbon chromium bearing steel
- NSK (Nippon Seiko) Single Row Deep Groove Ball Bearing 6200 Series ZZSingle row deep groove ball bearings are the most typical type of rolling bearings and have a wide range of uses. The orbital grooves provided on the inner and outer rings form a cross section of an arc having a radius slightly larger than the radius of the rolling ball. In addition to radial loa... Read MoreRemark - Mounting Dimension (Minimum Dx) (Φmm) - Mounting Dimensions (Maximum Cx) (mm) -
- MonotaRO Deep Groove Ball Bearings 6200 Series ZZ* Do not use for anything other than its intended purpose.Material (Main Unit) High carbon chromium bearing steel Shield Shape Double-sided steel plate shield type Load Direction Radial Outer Ring Type Flat Race Ring Shape Deep groove ball bearings Number of Track Trains Single row
- TSUBAKI (Tsubakimoto Chain) RS Roller Chain Single RowA large reduction ratio can be obtained. (Generally up to 1:7) A relatively long distance between axes (usually 4m or less) can be obtained. There is a large degree of freedom in the distance between shafts. Multi-axis transmission is possible. Both sides are available. Easy to install and replac... Read MoreIncluded Accessories With 1 connecting link Material (Main Unit) Steel Type Roller chain Single or Double Strand 1
- NMB (Minebea) DDL-ZZ Series Thin Double Shield Radial Ball BearingIt is a miniature bearing that is often used in information and communication equipment centered on personal computers, home appliances, and control motors for automobiles. It is a precision part used for the part that receives the shaft in order to stably rotate the shaft of rotating equipment t... Read MoreMaterial (Main Unit) Martensitic stainless steel JIS Grade 0 Load Direction Radial Outer Ring Type Flat Race Ring Shape Deep groove ball bearings Number of Track Trains Single row Rolling Element Material Martensitic stainless steel
- NTN Deep Groove Ball Bearings 6200 Series LLB (Double Non-Contact Rubber Seal Type)Deep groove ball bearings that are most widely used among bearings. Deep groove ball bearings have deep arcuate grooves on both the inner and outer rings, and can receive radial loads, axial loads in both directions, or combined loads that are a combination of these, making them suitable for high... Read MoreMaterial (Main Unit) High carbon chromium bearing steel JIS Grade 0 Shield Shape Non-contact seal type on both sides Load Direction Radial Outer Ring Type Flat Race Ring Shape Deep groove ball bearings Number of Track Trains Single row Rolling Element Material High carbon chromium bearing steel
- MonotaRO Set Collar StandardThis is convenient when you want to adjust the position. * Do not use for anything other than its intended purpose.Type Standard Material S45C Surface Treatment Black dyed
- MonotaRO Deep Groove Ball Bearings 6000 Series ZZ* Do not use for anything other than its intended purpose.Material (Main Unit) High carbon chromium bearing steel Shield Shape Double-sided steel plate shield type Load Direction Radial Outer Ring Type Flat Race Ring Shape Deep groove ball bearings Number of Track Trains Single row
- TAKIGEN MFG Grommet with Flame Retardant FilmUses flame-retardant material (UL94V-0 compliant). You can choose from a wide variety of types according to your needs. It can be set in the hole of the panel with one touch. Non-migratory rubber (contamination test JIS K6267 no abnormality) Distribution board / control board / measuring equipmentMaterial EPDM Color Black Type Grommet Operating Temperature Range (℃) Up to 70 Hardness 50°±5° Operation Ambient Temperature (℃) Up to 70 Feature Flame retardance
- Mitsuboshi Belting V belt C type (standard)It is a set-free belt that does not stretch or shrink during use and is suitable for multiple hangings, and can be expected to have a long belt life. In addition, it is easy to obtain by handling it as a standard V-belt.Type V-belt Operating Temperature Range (℃) -40~70 Offset Angle (°) 40 Electrical Resistance Value 50MΩ or more Belt Shape C
- MonotaRO Stud BoltFor positioning jigs during mold processing. * Please refrain from using it for any other purpose.Material S45C Surface Treatment Homo processing Hardness HRC 25~30 Heat Treatment Yes
- Kurashiki Kako Anti-Vibration Pad (Natural Rubber, Rubber Hardness 50)Easy to install and move Machines can be easily installed and moved. It can be cut to an appropriate size with scissors and a knife at the site, and it is effective just by laying it under the machine. A special pattern is applied to both sides, which has a large anti-vibration effect, and a rela... Read MoreMaterial Natural rubber (rubber hardness 50) Specific Vibration Frequency (Hz) - Rubber hardness (JIS)50 Support surface pressure (N / mm 2 ) - Cut-off frequency (Hz) -
- SUS T Nut SS (M5)Suitable for SF20 series Material S10C equivalent, UNIQLO plating Mass (g) 2 Type M5
- MABUCHI MOTOR DC MotorIt is a motor widely used for work. Country of origin: China Models, crafts, etc. * Performance table when using AA batteries. (FA, RE series) * Performance table when using a constant voltage power supply. (RS series)Type General-purpose motor Type of Sign Tap With or Without Brake None Power Supply DC Motor Type Brushed motor Operation Environment Indoor (normal temperature and humidity) Number of poles (P) 3
- TSUBAKI NAKASHIMA Steel Ball (Precision Ball) SUJ2 inch SizeBall bearings are used in rotating parts of automobiles, home appliances, motorcycles, and general machinery. Ball bearings, slide rails, ballpoint pens, seat belts, valves, bicycles, casters, door rollers, ball millsHardness HRC 62~67
- IMAO Anti-Vibration Rubber (Male Screw / Female Screw)By attenuating and absorbing vibrations from operating machines, noise and adverse effects on adjacent machines are prevented, and the life of machinery and equipment is extended.Shape Round type Type of Connection Female thread / male thread Color (Body) Black Material (Anti-Vibration Rubber) Natural rubber Suitable Usage Anti-vibration
- ACE Aluminum Extrusion 3030 Type StandardShape Square Material (Main Unit) A6063S-T5 Type 4-sided groove Number of Flutes 1 row groove x 1 row groove Elongation (%) 8 or more Tensile Strength (N/mm2) 245 or more Yield Strength (N/mm2) 215 or more Surface Treatment (Main Unit) White anodized
- TRUSCO Key Material S45C (New JIS Parallel Double-Sided Square Key Standard Product)You can cut it to the required length and use it. A detent for the joint between the shaft of a motor or reducer and the gear or sprocket.Shape Double-sided key Tolerance JIS B 1301
- ACE Aluminum frame nut / holder set (rear insertion type) □ 30 seriesSuitable for □ 30 series Set Contents Nut holder, nut holder HA06WH (white) Surface Treatment Square nut / fabric
- ACE Aluminum Extrusion 2020 Type StandardShape Square Material (Main Unit) A6063S-T5 Type 4-sided groove Number of Flutes 1 row groove x 1 row groove Elongation (%) 8 or more Tensile Strength (N/mm2) 245 or more Yield Strength (N/mm2) 215 or more Surface Treatment (Main Unit) White anodized
- Mitsuboshi Belting Pencil Type Tension MeterA standard spring-loaded tension measuring machine. It can be used for standard V-belt, red label V-belt, e-power series, and ultra e-power V-belt. V-belt tension measurementMaterial Steel sheet Mass (g) 65 RoHS directive (corresponding to 10 substances) Correspondence
- MonotaRO Revolving Grip* Do not use for anything other than its intended purpose.Color Black Material (Screw) Iron Material (handle) Unsaturated polyester resin
- Iwata Mfg. Rubber Edge TrimA compact trim that is easy to cut and bend because there is no core metal.RoHS directive (corresponding to 10 substances) Correspondence
- No Brand Resin Ball (Urethane) (Inch Size)Material Urethane Hardness HS95
- OILES Oiles # 80 BushOILES # 80 is a non-lubricated bearing in which lubricating oil and a special filler are uniformly dispersed and contained in the resin in polyacetal. It can be used without lubrication and has excellent load resistance and wear resistance. It has a low coefficient of friction and excellent speed... Read MoreType # 80 Bush Material Oil-impregnated polyacetal resin Operating Temperature Range (℃) -40~+80 Hardness HRM72 Elongation at Break (%) 60 Lubrication System No lubrication Specific Gravity 1.39 Melting Point (℃) 165 Bending Strength (N/mm2) 76.5 Allowable PV Value (N/mm 2 m/s) [kgf/cm2 m/min] 2.45[1500] Allowable Maximum Surface Pressure P (N/mm2 [kgf/cm2]) 17.5[179] Linear Expansion Coefficient (×10-5/℃) 8~13 Tensile Strength (N/mm2) 51.0 Flexural Modulus (N/mm2[kgf /cm2]) 2650[27000] Izod Impact Strength (J/m[kgfcm/cm]) 58.8 [6.00] (with notch)
- NSK (Nippon Seiko) Single Row Deep Groove Ball Bearings 6900 Series DDU (Both Sides Contact Rubber Seal Type)Material (Main Unit) High carbon chromium bearing steel JIS Grade 0 Shield Shape Double contact seal type Load Direction Radial Outer Ring Type Flat Race Ring Shape Deep groove ball bearings Number of Track Trains Single row Rolling Element Material High carbon chromium bearing steel
- SHK Press Spring Material Spring Hard Steel Wire SWC Unichrome PlatedElectronic parts, electrical appliances, toys, industrial equipment, etc. * Please do not use it in a deformed or damaged state.Material Spring hard wire SWC UNIQLO
- TSUBAKI NAKASHIMA Steel Ball (Precision Ball) SUS440C mm SizeThis stainless steel has excellent mechanical properties by being cured by heat treatment. This feature is suitable for ball bearings, valves, etc. Ball bearings, slide rails, ballpoint pens, seat belts, valves, bicycles, casters, door rollers, ball millsMaterial SUS440C Hardness HRC 58~65 Gauge Pitch (μm) 2.0 Gauge S (μm) +10~-10
- WAKI Anti-Vibration Rubber MatIt is highly wear resistant and elastic, and has excellent mechanical properties. The ground plane is slightly yellowed. It cannot be used in places where petroleum or chemicals come into contact. Please use within -20 ℃ ~ + 60 ℃. For vibration isolation of washing machines, audio, outdoor units... Read MoreMaterial NR (natural rubber) Rubber hardness 60±5 RoHS directive (corresponding to 10 substances) Correspondence
- NSK (Nippon Seiko) Stainless Bearing Double Shield TypeStainless steel bearings are the basic product of NSK special environmental bearing Spacia TM series, and are mainly suitable for high humidity environment. The lineup is affordable. Corrosion resistance superior to bearing steel. For air only, grease lubrication. The cage is made of glass fiber ... Read MoreJIS Grade 0 Shield Shape Shielded on both sides Load Direction Radial Outer Ring Type Flat Race Ring Shape Deep groove ball bearings Number of Track Trains Single row
- SUPER TOOL T Slot BoltA bolt diameter of the same size as the table T-groove can be used. A special bolt made by precision forging carbon steel. For fixing the clamp (jig tool) to the table.
- NSK (Nippon Seiko) Single Thrust Ball Bearings 51100 SeriesThrust bearings have a contact angle of more than 30 ° and less than 90 °, primarily supporting axial loads. There is a ball between a set of track boards (axial track board and hizing track board), and the contact angle is usually 90 °. Only unidirectional axial loads can be applied, not radial ... Read More
Filter by categories