It is a set-free belt that does not stretch or shrink over time during use and is suitable for multiple hangings, and can be expected to have a long belt life. In addition, it is easy to obtain by handling it as a standard V-belt.
Type V-belt Operating Temperature Range (℃) -40~+70 Offset Angle (°) 40 Electrical Resistance Value 50MΩ or more Material (Belt) Rubber Belt Shape B
A large reduction ratio can be obtained. (Generally up to 1:7) A relatively long distance between axes (usually 4m or less) can be obtained. There is a large degree of freedom in the distance between shafts. Multi-axis transmission is possible. Both sides are available. Easy to install and replac... Read More
Included Accessories With 1 connecting link Material (Main Unit) Steel Type Roller chain Single or Double Strand 1
It is a set-free belt that does not stretch or shrink during use and is suitable for multiple hangings, and can be expected to have a long belt life. In addition, it is easy to obtain by handling it as a standard V-belt.
Type V-belt Operating Temperature Range (℃) -40~70 Offset Angle (°) 40 Electrical Resistance Value 50MΩ or more Belt Shape C
A standard spring-loaded tension measuring machine. It can be used for standard V-belt, red label V-belt, e-power series, and ultra e-power V-belt.
V-belt tension measurement
Material Steel sheet Mass (g) 65 RoHS directive (corresponding to 10 substances) Correspondence
This is the highest quality pulley that exceeds the JIS standard (JIS B1854-1987 "general V pulley") in terms of material, processing accuracy, and balance accuracy. The disproportionate tolerance on the outer circumference is guaranteed to be 0.1% of the pulley mass. The surface treatm... Read More
Number of Flutes 1 Pilot Hole Diameter (Φmm) - Rim Width w (mm) 20 Groove Shape A
A set of pulleys that can be used as a power transmission system or deceleration unit. You can also reverse the rotation by tapping the rubber. In addition to the pulleys of three sizes, the bearing bushes are compatible with the 3mm hexagonal shafts of the work series, 2mm and 3mm round shafts, ... Read More
The largest usage record in Japan. It demonstrates high reliability. It is a completed V pulley with high quality and high balance accuracy.
* The pilot hole is not open. Please note that additional machining such as hole machining and keyway machining cannot be supported.
Number of Flutes 2 Rim Width w (mm) 44 Groove Shape B
You can easily make a power unit by combining pulleys. Five sizes of pulleys, bushes, thread rubber, etc. are included, and it is possible to change the speed and power according to the work. The motor holder and pulley stay are mounted together on a resin base and can be widely used for devising... Read More
We have a wide variety of modules, number of teeth, etc., and are inexpensive and highly applicable.
* The accuracy grade is "equivalent".
Type Spur gear Material S45C Module 0.5 Surface Treatment Black dyed Pressure Angle (°) 20 Tooth Type Normal teeth Tooth Surface Hardness 194HB or less Gear Surface Treatment Cutting Tolerance A H7 Gear Cutting Reference Plane Hole Web Thickness H (mm) - Rim Diameter I (Φmm) -
The Type 1 Isomec bushing has two half-drilled holes and one half-screw hole, for a total of three holes. In addition, the Isomec pulley has a screw hole at the position corresponding to the screw hole of the bushing and a drill hole at the position corresponding to the screw hole of the bushing.... Read More
Type 1 Allowable Transmission Torque (Nm) 3000 Set screw Length (inch) 1 1/4 Number of Set Screws 2 Nominal Size of Set Screw (inch) W5/8 RoHS directive (corresponding to 10 substances) Correspondence
* The pilot hole diameter is the hole diameter that is pre-drilled at the time of purchase, and the maximum shaft hole diameter is the maximum hole diameter that can be machined. Please note that we cannot handle hole processing.
Achieves high precision, high load and low noise with a new arc tooth profile. A toothed belt with a new arc tooth shape that uses involute meshing. The pulley tooth shape and belt tooth shape created by the involute movement are approximated to the utmost limit to achieve excellent transmission ... Read More
Material (Main Unit) Chloroprene rubber Type GT belt Material (Tooth Cloth) Nylon canvas Material (Core Wire) Fiberglass cord Belt Shape 5GT
The Schmidt coupling is a misaligned joint that uses the crank motion of the link. The shaft can be moved in parallel. It can be driven freely within the displacement range of the driven shaft when the rotation is stopped or during load operation. Absorbs sliding and absorbs radial sliding on the... Read More
Material (Main Unit) S45C equivalent Type Schmitt coupling
Included Accessories Set screw Type Complete Miter Material S45C Reduction Ratio 1 Shape BK Number of Teeth 20 Surface Treatment Black dyed Pressure Angle (°) 20 Heat Treatment Tooth surface induction hardening Tooth Type Gleason Accuracy Class JIS B 1704 Class 4 Tooth Surface Hardness 48~53HRC Gear Surface Treatment Cutting Tolerance A H7 Gear Cutting Reference Plane Hole Tip Cone Angle L 49 degrees 48 minutes
Common specifications for vibration High-quality special plastic material (Zytel) is used for high-rigidity and high-strength cushioning material. It is hard in the twisting direction and has excellent flexibility in the twisting and axial directions. Almost no maintenance is required. Compact It... Read More
Achieves high precision, high load and low noise with a new arc tooth profile. A toothed belt with a new arc tooth shape that uses involute meshing. The pulley tooth shape and belt tooth shape created by the involute movement are approximated to the utmost limit to achieve excellent transmission ... Read More
Material (Main Unit) Chloroprene rubber Type GT belt Belt Nominal Width 50 Material (Tooth Cloth) Nylon canvas Material (Core Wire) Fiberglass cord Belt Shape 8YU
Material (Main Unit) A2017 Mass (g) 84 Type Disc type Maximum Rotation Speed (min-1[rpm]) 16000 Maximum Torque (Nm) 24 Regular Torque (Nm) 12 Thread Size M M4 Material (Disc) SUS304 Material (Bolt) SCM435 / iron trioxide coating (black) Allowable Deviation Angle (°) 1 Static Torsion Spring Constant (Nm/rad) 6000 Material (Collar) SUS304 Screw Tightening Torque (N・M) 3.5
With the unique pitch diameter adjustment mechanism, the adjustment range is wide and it can be set every 1/4 rotation of the slide piece, so delicate speed setting is possible. To adjust the pitch diameter, simply loosen the set screw, turn the slide piece the specified number of turns, and then... Read More
The length of the free length series can be freely specified in 1 mm increments. We use high-precision cold drawing material to guarantee accuracy and minimize variations in lots. SUS316 is used for the stainless steel material to improve corrosion resistance.