Screw Supports

Clamp support Jack attachments can be used.

For positioning jigs during mold processing. * Please refrain from using it for any other purpose.

When the steel ball is set on the cradle, a contact surface with low friction is obtained, and adjustment is smooth with a light force.

For press machines, the diameter of the upper surface of the head is large. For adjusting the height of the clamp.

Clamp support screw jacks are useful for supporting various clamps. If one screw does not work well or the height is not high, you can stack two or three screws. (Same size only) The attachment is also convenient for supporting irregular shapes.

Especially convenient for centering work of workpieces that are uneven like a casting surface.

It is a support for the clamp. Convenient for height adjustment. Clamp support. Adjusting the height of the work piece. * Make sure that the clamp is not tilted up / down or left / right. Note that parallelism is difficult to obtain if chips are pinched when setting.

Since it is made of aluminum, it will not damage the base, clamps, etc. Convenient as a support jack for plastic clamp sets.

The work is firmly supported with a three-stage configuration consisting of the main body, intermediate male screw, and upper male screw that receives the load. Easy to grasp and turn. Do not damage the work. Long stroke. Hard to loosen with lock screws. Easy operation with positioning, fine adju... Read More

Ideal for use with the Uniclamp body (FGB / FPB-B). The swivel nut has a spherical bag shape and can be tilted up to 6 ° back and forth and left and right.

Supports various clamps. * Please use the support tip (sold separately) to support uneven surfaces and irregular shapes. * When using the support in a stackable manner, be sure to use the connection bracket (sold separately).

Can be used for screw supports, large screw supports, and magnesium jacks. To support irregular shapes

A dedicated screw support tip for all types of workpieces. A tip with a ball brander that does not come off easily.

Can be used for vertical and horizontal jigs Since the magnetic force is built into the bottom of the main body, chips do not adhere. Use a support tip (sold separately) for uneven surfaces and workpieces with irregular shapes.

EA637EA / EA637EB series jack mounting attachment Spherical receiving pad

EA637EP-1 to -3 pads can be attached.

EA637EP-1 to -3 pads can be attached.

Can be used for horizontal and vertical jigs. Since the magnetic force is built into the bottom of the main body, there is no adhesion of chips. Use the support tip for uneven surfaces and workpieces with irregular shapes.

Prevents misalignment when using stacked screw supports. For screw support joints * Check the body diameter of the support and the hole diameter of the metal fittings before using.

The work is firmly supported with a three-stage configuration consisting of the main body, intermediate male screw, and upper male screw that receives the load. The magnetic force that can be used for horizontal and vertical jigs is built into the bottom of the main unit. Hard to loosen with lock... Read More

EA637EA / EA637EB series jack mounting attachment V-groove receiving pad

Screw support for large machines Long stroke type Joint support for FS500LS. Joint support By adding FSJ200, the height is increased by 200mm. Up to 2 levels can be added! Withstand load ・ When one unit is installed: 120kN (total length 500-700mm) For load / 2 units mounting: 100kN (total len... Read More

Ideal for use with the Uniclamp body (FGB / FPB-B). The swivel nut has a spherical bag shape and can be tilted up to 6 ° back and forth and left and right.

It is a support for the clamp. It is a support for the work piece. You can position the height, etc. Clamp support. Adjusting the height of the work piece. * Make sure that the clamp is not tilted up / down or left / right.

Ideal for supporting workpieces and clamps used in large machines. Since it uses a double-threaded screw and a reverse screw, it can be fast-forwarded by 16 mm (down) per rotation of the intermediate male screw. By using aluminum for the main body, the mass is cut by 25% (compared to the company)... Read More