Steering / Transmission Related Tools

As it is a simple type, no installation work is required. Compact and lightweight, easy to move. Separate type that can be used for vehicles of various widths. The total length is short and it can be installed in a small space. The height of the main body is low (28 mm) and it has a slope for smo... Read More

Side slip board set This is the step board that comes with the ATG92.

Used for disassembling the rear wheel of a truck.

A special tool for assembling the front hub and knuckle of FF vehicles. By using it together with the bearing race puller, it is possible to disassemble the knuckle arm and hub other than the strut type.

For Volkswagen Audi front wheel hub (V10.1) The claws are specially designed to be sharper than other pullers. For Volkswagen Audi front wheel hubs (V10.1).

If you use this tool, you can remove the high temperature drain bolt without touching it directly with the strong magnet at the tip, so if you open the drain bolt when changing the oil of the car, you will be exposed to hot and dirty oil, or the tool And the floor will not get dirty. After loosen... Read More

A set of pilot bearing pullers that can be pulled out by hooking the claws of the main body on the inner collar of the inner bearing type bearing. Attach an attachment that matches the inner diameter size of the bearing and connect it to the main body. ・ After that, the bearing can be pulled out... Read More

A set of pullers that pull out gears, bearings, pulleys, etc. It is a set that comes with two types of separators and bolts with diameters of 30 to 50 mm and 50 to 75 mm. Since the separator can be used in combination with a press, bearings and gears that are stuck to the shaft can be separated u... Read More

The slide hammer set is a convenient product that allows you to pull out hubs, oil seals, bushes, axle shafts, bearings, etc. from light sheet metal work by replacing the attached attachment. From light sheet metal work to pulling out hubs, oil seals, bushes, axle shafts, bearings, etc. * Please ... Read More

Used when tightening the boot band of drive shaft boots. Also, since it has a cutter, you can cut extra parts. Tightening or cutting the boot band of the drive shaft * Please do not use it for any purpose other than its intended purpose. * Cannot be used for perm quick boot bands.

The tie rod end and ball joint can be easily separated. Comes with a fall-prevention string for work safety. Compatible with light cars to passenger cars. For separating tie rod ends and ball joints. * It may not be possible depending on the model.

It is a spare part for the ball joint boot tool set ATS4111 and the ball joint boot inserter set ATS4110.

Since it has 3 claws, it can be firmly fixed. For removing pilot bearings and hub bearings. * Do not use for any other purpose. * Please wear protective equipment such as gloves and glasses when working. * This product is a removal-only tool. * Do not use with a power tool such as an impact wrenc... Read More

A spring catch plate is attached to prevent it from falling off. It is durable because the screw diameter is as thick as about 18.5 mm. For attachment / detachment of coil spring * Cannot be used with an impact wrench. Apply grease to the threads before use. * It may not be possible depending on ... Read More

A type of separator that hits into the gap of the ball joint For removing the ball joint. * Please refrain from using it for any other purpose. Do not pry or twist this product when working.

An aluminum screwdriver used when driving bearings, oil seals, and bearing races. For driving bearings and seals * Do not use for anything other than its intended purpose. * Be sure to use an attachment that matches the size of the object. * When you type in, please type in straight and carefully.

By adopting a 17mm hexagonal drive, it is possible to work even in narrow places with obstacles. Stable fastening work of the drain plug is realized by making the square convex dimension 10.0 mm. By setting the drive angle to 9.5 sq., Which is the mainstream for automobile maintenance, work effic... Read More

It is a plier for the caulking type boot band that can be attached by caulking a caulking type band such as a drive shaft or a radiator hose. You can also adjust the torque when tightening the stainless band by extending it using a socket handle with a drive angle of 12.7 mm (1/2) or by using a t... Read More

Can be used with an impact wrench! With bearings For struts

It is a tool for centering the clutch disc, which is indispensable when overhauling the clutch of FR cars. Use a combination of accessories suitable for the pilot bearing diameter of the vehicle to be worked on and the size of the diaphragm of the clutch disc cover. For single clutch disc * Pleas... Read More

Press-fit type tie rod (ball joint) A socket used when driving end boots, and can be easily installed. For mounting tie rods (ball joints) and end boots (press-fit type). * Do not use for any purpose other than its intended purpose.

This shape is also used for oil pans and undercarriage bolts of European cars.

Used to remove the ball joint.

A tool used to center the clutch. Ideal for FF vehicles without pilot bearings or metal bushes. The body is made of all resin and is light and durable. For centering the clutch * Do not use for any other purpose.

By adopting 12.7sq., It can be used for drain plugs that are tightened with a large torque. Since the main body has a hexagonal shape, it is possible to use a 24 mm wrench. A special tool for tightening and loosening the differential drain (filler) plugs used in Nissan and Subaru vehicles.

Ideal for removing ball joints from 4t vehicles to large vehicles. Impact wrench compatible (low speed use of 5000 RPM or less) For separating the tie rod and knuckle arm. * Do not use for anything other than its intended purpose.

The lock nut can be crimped and crimped with this one! Due to the shape of the tip boat, you can crimp cleanly just by pushing in and hitting. The grip is made of rubber, which is easy to grip, and has a brim, so it is difficult to accidentally clap your hands. Strong because it is a forged produ... Read More

For bolts and nuts whose corners have been licked. Can be used for both loosening and tightening. It has a patented special shape and is different from conventional extractors.

A tool for attaching and detaching the drain plug when changing engine oil, mission oil, differential oil, hydraulic oil, etc. For attaching and detaching the drain plug * Do not use for any other purpose.

Convenient for driving bearings and seals.

For removing the steering of your car

A slide hammer set for pulling out parts with service taps.

For spring replacement work.

It can be used for a wide range of vehicles by sliding the pins to match the appropriate pitch. Since there is a scale display on the main body, it is easy to center. Tightening and loosening of the rear hosing nut.

Convenient for removing flywheels for small engines such as motorcycles, farm equipment, mowers, and outboard motors.

Convenient for driving bearings and seals.

Even bearings that do not have a puller on the inner and outer diameters of the bearing can be pulled out. For pulling out ball bearings * Please do not use for any other purpose