Hand Taps

It is a general tap and is used in all directions. For 3rd grade gauge

A clean female screw can be set up.

A set of general hand taps for cutting female threads. It is a 3-piece set with 9 mountains (first # 1), 5 mountains (middle # 2), and 1.5 mountains (top # 3). It is mainly used when manually cutting a thread or when correcting a thread. For thread cutting and thread correction of general female ... Read More

A general hand tap that cuts the thread of a female thread. The bite part is a tap in 5 mountains (2nd tap). It is mainly used when manually cutting a thread or when correcting a thread. For thread cutting and thread correction of general female threads. * Be sure to wear protective equipment whe... Read More

It is a general tap and is used in all directions.

Both through holes and blind holes can be used. High speed steel (HSS-E) tap set. Work Material: General Steel, Low / Medium Carbon Steel, Alloy Steel.

A general hand tap that cuts the thread of a female thread. The bite part is the tip tap (1st tap) of 9 mountains. It is mainly used at the beginning of manual thread cutting. As the first tool for thread cutting of general female threads. * Be sure to wear protective equipment when using as ther... Read More

A general hand tap that cuts the thread of a female thread. The bite part is 1.5 mountain top tap (3rd tap). It is mainly used at the beginning of manual thread cutting. For the final finish of general female thread threading. * Be sure to wear protective equipment when using as there is a risk o... Read More

A set of 3 for roughing, medium finishing, and finishing. Deep hole female screwing is also possible by using 3 taps. For female threading of general steel, brass, copper, aluminum, and resin. * M2 x 0.4 to M7 x 1.0 have a convex tip.

It is a dedicated tap that cuts the tap groove for inserting the sprue. That is, it is larger by the sprue wire diameter than the normal tap with the same nominal diameter of the applicable screw. Work material: Soft material such as aluminum.

* If you order by cash on delivery, it may be shipped the next day or later.

It is a general tap and is used in all directions. * Depending on the size, it may be a protruding center, unlike the posted image.

It can be attached to models with forward and reverse rotation such as impact drivers, and screw holes can be easily machined. Thread formation For repairing crushed threads * Cannot be used for power tools other than those with forward and reverse rotation. Be sure to use tapping oil.

It can be attached to a tap handle, etc., and can be screwed up. Since it is a tap for medium finishing, it is ideal for thin plates. For internal thread cutting of general steel, brass, copper, aluminum, and resin, and regeneration of crushed threads.

The shank of the standard tap is lengthened, and it is used when the threaded part of the standard tap protrudes and the length is insufficient. Work Material: Carbon Steel, Tool Steel, Alloy Steel, Cast Iron, Ductile Cast Iron, Brass, Aluminum Alloy Casting, Zinc Die Casting.

It is used when making screw holes and removing (cleaning) them. For repairing and manufacturing coarse threads. Work Material: Iron, Light Metal. Correction and fabrication of coarse threads. * Cannot be used for stainless steel screws.

A tap (# 2) used to set up a general screw, mainly for screw thread correction.

A tap (# 2) used to set up a general screw for a left-hand screw (reverse screw).

It is used when making screw holes and removing (cleaning) them. For repairing and manufacturing coarse threads. Work Material: Iron, Light Metal. Correction and fabrication of coarse threads. * Cannot be used for stainless steel screws.

It is a general tap and is used in all directions.

A tap used to set up general screws, mainly for screw thread correction (# 2).

A set of 3 taps, tip (# 1), middle (# 2), and top (# 3), which are used to set up general screws.

* If you order by cash on delivery, it may be shipped the next day or later.

It is used when making screw holes and removing (cleaning) them. For repairing and manufacturing coarse threads. Work Material: Iron, Light Metal. Correction and fabrication of coarse threads. * Cannot be used for stainless steel screws.

Threads can be easily set with an electric impact driver. Uses high quality HSS material.

It is used when making screw holes and removing (cleaning) them. For repairing and manufacturing coarse threads. Work Material: Iron, Light Metal, Coarse Thread Correction, Manufacture * Cannot be used for stainless steel screws.