The reviews are automatic translation.
Used for the front fork of address v125
On 2019-05-22 08:23:10
Used to load thrust bearings on the front fork at address v125. If you find something you can not find even if you straddle your home improvement center, you can buy at Monotaroo at a low price. Because even if it is a genuine fork, even the joint of a manhole and an end has a shocking uplift, I was initially thinking about the initial adjustment of the fork with a washer or nut filling. As an alternative, if you want to pack it, put a thrust bearing in this washer and increase the oil to 15w. In addition, when the reinforcement spring was inserted and the oil level was adjusted, all complaints around the front could be resolved. Our vehicle is a k6 model and uses a lowdown with a spring for k7. The oil surface calmed down at 98mm when I tried some patterns. I think that oil level adjustment is contributing to the push-up cancellation, but when we tried without washer + thrust bearing, the initial operation could be felt very well if there was a thrust bearing, and it was replaced with a high-class fork I raise it until the illusion.
On 2018-12-27 02:01:53
It was very easy to use. It was good to purchase.
Subaru car shift linkage
On 2018-12-14 16:01:46
We used it for full bearing of Shinku linkage of Subaru car.
It is convenient because you can compare and compare various materials.
Used for repairing machines
On 2018-09-04 18:54:48
I tried to buy it by the price.
I can use it without problems.
I think I would like to use this next item as well.
On a bike
On 2018-07-30 14:44:46
We built it in the front fork of YAMAHA SDR together with the bearing. The feeling of thrusting donkey is good.
Along with thrust together with bearing
On 2018-07-23 11:54:04
I think that it is production by pressing because it is inexpensive.
Although the inner diameter is slightly large, since precision etc. are not written
If it is a fit, it is an in-kind match.
Because it is thin, as it is suppressed by the surface with precision and width as it is,
In addition, it is necessary to guide the position by outer shape or inner diameter.
It is cheap and good.
Used to eliminate the play of the snowplow link part
On 2018-03-25 17:18:28
Diameter was accurate and finish was perfectly satisfactory Diversion was correct as spacer for both price and quality
As a spacer
On 2018-01-25 15:39:47
This time I purchased it as a gap filling It is the best to fill a gap that is a little concerned The unit price is also low, so it can be used without worrying about the cost
Setting up a competition vehicle
On 2017-12-24 01:29:18
On the receiving side of NTN thrust bearing
People who can not buy Hi Paco's Pace are here
I think that it is possible to obtain almost similar effects.
Considering the expenditure, the person who was throwing away cheap things thinks about the cost ○
Although there are other spring bearing seats of the internal organs of the bearing, there are things that can not be installed unless shocks are affordable in case of using up and down as there is a thickness, and the car height can not be lowered.
□ good point
· Inexpensive (Although it is not the original use of the product, it is inexpensive as a spring seat of a bearing built-in)
· Thickness is thin (There is a degree of freedom in setting since it is not so thick.)
□ Bad point
· There is invasion of sand etc inside (There is a product that makes sand using the same bearing harder to penetrate, those who are interested are there)
· Rust caused by rain etc. (Apply grease to the bearing and take measures against rust.)
· Maintenance free is impossible (Sometimes it is necessary to remove sand and garbage.)
I tried wearing it by trial, but I felt the effect more than I thought.
□ Felt effect
· Decrease in thrusting when crossing a step (High rate may be better.)
· Steering operation is intelligent or smooth (at the same time the alignment was also adjusted, so what is the effect?)
- I think that the seat loosening due to the twist of the spring and noise suppression measures will be taken. (The effect seems to be big with struts)
It is not a part of the time things such as the circuit etc in the city ride improvement item.
It seems that taste also divides preferences.
The installation was done only on the upper side, but it seems that the effect will rise if it is caught up and down.
Bearings under the upper mount (under the upper seat) are adopted as genuine even by Porsche and other manufacturers, and the effect is the seal of effect?
1992 bike custom
On 2017-03-31 13:21:36
I bought it as the opponent side of the thrust bearing on the spring seat of the suspension. It can be used with confidence as it is for bearing.