The reviews are automatic translation.
On 2018-07-12 00:15:34
I use it as a front fork of a motorcycle, but the best cost performance
Modification of a commercially available tool
On 2018-06-29 14:54:10
It is a tool that occupies the nut and works, but the load is considerable. I built this product so that it can be easily tightened. It is quite good. Bearings are purchased via Mr. Monotaro.
On 2018-06-27 05:31:26
Used for attaching the suspension. Friction decreased when the spring stretched. I also want to purchase it when necessary.
Axis of rotary chair
On 2018-05-25 22:22:34
I was impressed by the turning of the chair. It is as per the standard and there is no problem.
Used for bike forks
On 2018-05-01 14:51:23
Just for the front fork of my car. The suspension 's movement improved dramatically, suppleness increased. The front suspension of the NC 700X was the worst according to the price, but by placing the product on the top of the coil spring and making the twist smooth, the suspension performance improved.
On 2018-03-23 22:25:46
It is a wonderful performance. Prices are also kept low, I am thankful.
On 2018-02-15 20:48:41
I use it for the rear suspension of a motorbike.
Because the thickness is 5 mm with two washers and bearings, it fits within the adjustment range.
Since the bearing escapes the twisted portion of the spring even if the suspension is set stiff
The feeling of ride improves with a feeling soft!
On the motorcycle front fork
On 2018-01-22 15:18:00
It came pretty major in cars, but in bikes it's a custom from now on.
41 mm Used for forks made by Showa. It got stuck on the stroke and became smooth.
It is pretty good custom of COSPA.
Setting up a competition vehicle
On 2017-12-24 01:31:41
People who can not buy Hi Paco's Pace are here
I think that it is possible to obtain almost similar effects.
Considering the expenditure, the person who was throwing away cheap things thinks about the cost ○
Although there are other spring bearing seats of the internal organs of the bearing, there are things that can not be installed unless shocks are affordable in case of using up and down as there is a thickness, and the car height can not be lowered.
□ good point
· Inexpensive (Although it is not the original use of the product, it is inexpensive as a spring seat of a bearing built-in)
· Thickness is thin (There is a degree of freedom in setting since it is not so thick.)
□ Bad point
· There is invasion of sand etc inside (There is a product that makes sand using the same bearing harder to penetrate, those who are interested are there)
I would like you to list similar products of the same size if there are ...
· Rust caused by rain etc. (Apply grease to the bearing and take measures against rust.)
· Maintenance free is impossible (Sometimes it is necessary to remove sand and garbage.)
I tried wearing it by trial, but I felt the effect more than I thought.
□ Felt effect
· Decrease in thrusting when crossing a step (High rate may be better.)
· Steering operation is intelligent or smooth (at the same time the alignment was also adjusted, so what is the effect?)
- I think that the seat loosening due to the twist of the spring and noise suppression measures will be taken. (The effect seems to be big with struts)
It is not a part of the time things such as the circuit etc in the city ride improvement item.
It seems that taste also divides preferences.
The installation was done only on the upper side, but it seems that the effect will rise if it is caught up and down.
Bearings under the upper mount (under the upper seat) are adopted as genuine even by Porsche and other manufacturers, and the effect is the seal of effect?
Used as a front fork of a single car
On 2017-12-17 23:07:23
Purchased with a washer of the same diameter and set. The behavior of the motorcycle changes easily and it is interesting.