|
|
Machine Key S45C New Jis Parallel Morozumi Key Constant Length Product
[x]close
|
Machine Key S45C New Jis Parallel Morozumi Key Constant Length Product
(16)
|
Narrow by
* Products that meet your criteria are shown in
table below.
...see all>
|
Customers Who Viewed This Item Also Viewed
<<
>>
Machine Key S45C, Old Jis. Square Ended Parallel Key, Standard Measure Product
HINODE
2.99 - 85.99 SGD
Machine Key S45C Old Jis Parallel Double Ended Key, Standard Measurement Good
HINODE
23.99 - 199.99 SGD
Machine Key SUS304 New JIS Parallel Pararell Both Edge Key Cut Length
Osaka Spirit
19.99 - 309.99 SGD
Customer Reviews
The reviews are automatic translation.
Maintenance of air conditioners
From Japan
On 2018-07-07 16:42:03
45C and the material is hard, the surface polished state is good. Cut with a cana saw
It takes a while but I think that it can not be helped.
This review is about item#7169522.
Used for keyway of gear and timing pulley
From Japan
On 2018-06-24 06:55:52
Mr.Meister desktop lathe Compact 7 change gear set customized for others.
In Compact 7, the thread cutting pitch is
Mill thread: 0.5 / 0.7 / 0.75 / 0.8 / 1.0 / 1.25 mm
Inch screw: 12/20/22/28/32/36/38/40 mountain
Although it is supposed to be only possible,
Once calculated by an individual,
Mill thread: 0.4 / 0.45 / 0.6 / 0.9 / 1.5 / 2.0 / 3.0 / π (for worm gear) mm
Inch screw: 13/14/18/24/48 mountain others
You can do it. In case
However, one spur gear 20/40/45 tooth module 1 must be purchased and reworked.
(If you ask reworking separately to the manufacturer, it will be pretty expensive, so it is necessary to process with self-responsibility on the lathe.) * Reprocessing is not recommended by the manufacturer.
We expanded the shaft hole diameter by self-responsibility and attached a key groove with a sculpture sword.
In the future, I plan to bake the machine key so that an accurate and precise key groove can be put in it. (For polyacetal etc., limited to nonmetal.)
This review is about item#07169504.
During machine maintenance
From Japan
On 2018-03-07 13:38:03
It was inexpensive but it was able to be used without problems.
I also want to use it if I have the opportunity.
This review is about item#7169522.
Used for parts processing in vice + parallel block
From Japan
On 2017-12-02 22:30:57
Machine parts, there are taps and holes on the edge just as well. In that case, place it on the parallel block, and pinch it between the product and the vice claw and use it. Using around 5, 6 and 7, it is convenient to deal with most "troubled". The price is also cheap, very good.
This review is about item#7169522.
As a key material
From Japan
On 2017-03-24 16:10:56
Although it is used as a fixture, it has no problem.
This review is about item#7169617.
During part fabrication
From Japan
On 2017-03-17 14:49:55
I used it for the first time. It was cheap and the delivery was quick so it was saved.
This review is about item#7169617.
Key production
From Japan
On 2015-12-26 20:09:01
It is saved because it is instant delivery
This review is about item#07169671.
For jig
From Japan
On 2015-08-01 09:20:01
Purchased as jig material, I am satisfied
This review is about item#07169504.
Pulley of agricultural machinery etc, fixation of shaft
From Japan
On 2015-03-30 21:42:51
Since it is used mainly for remodeling etc., it cuts it to the necessary length and uses it, so if you purchase the size you often use it will be in time soon. I am happy that it is cheaper than anything.
This review is about item#07169522.
I used it to stop the rotation of the rotating shaft of the walking grass mower.
From Japan
On 2015-03-16 17:15:54
Since it is long, it was cut to the required length and used, the size I wanted was 4.0 mm x 5.0 mm. In fact, I bought two of 4.0 x 4.0 and 5.0 x 5.0 purchase, and in fact the repair was done using 4.0 x 4.0.
This review is about item#07169513.
