Insert bearing featured products

A bearing unit that combines a bearing and a bearing box with a square flange. Suitable for mounting on a vertical surface such as the side of a machine. The bearing box is attached to the machine body with four bolts. Adapter is not included.

A bearing unit that combines a ball bearing for the unit and a bearing box with a slide groove. By moving the bearing box in the radial direction along the slide groove, the support position at the center of the shaft can be adjusted. Belt conveyors, those that need to adjust the support position... Read More

A bearing unit that combines a ball bearing for the unit and a bearing box with a slide groove. By moving the bearing box in the radial direction along the slide groove, the support position at the center of the shaft can be adjusted.

A bearing unit that combines a bearing and a bearing box with a diamond-shaped flange. Suitable for mounting on a vertical surface such as the side of a machine. Compared to the square flange type unit, the mounting space is smaller and the unit mass is also smaller. The pitches of the two mounti... Read More

The new stainless steel housing has been redesigned and the laser-marked surface is so smooth that there are no places for water droplets to remain after washing. The smooth surface of the housing and the flat back solid mounting surface reduce the incidence of bacteria. All covers can be attache... Read More

OILES Pillow 80 is a self-aligning bearing composed of OILES # 80 and reinforced plastic. It is oil-free, lightweight, and has excellent rust resistance. It can be easily attached to places where it is difficult to form an oil film, and has excellent load resistance, wear resistance, and speed ch... Read More

A pillow type unit designed to reduce the mounting space. Mounting to the machine body is performed using the two screw holes provided on the bottom of the bearing box mounting.

Designed as a pillow-type unit for center height, it has high strength against impact loads. Ideal for applications where the dimension from the bottom of the mounting to the center of the shaft is large. The bearing box is attached to the machine body with two bolts.

A pillow-shaped unit designed for weight reduction. The bearing box is attached to the machine body with two bolts.

Compared to conventional ball bearing units, it is smaller and lighter, and the mechanical equipment is made more compact. Since the bearing box has a center mark, positioning is easy.

Reasonable self-aligning The bearing and the bearing box are completely sealed, so that only the bearing can be replaced due to the complete compatibility between the dust-proof bearing and the bearing box. Uses to maintain a beautiful luster for a long time with good adhesion of the coating film

Outer diameter measurement, inner diameter measurement, depth measurement, and step measurement are possible. Comes with a fine feed function. Calipers used for various dimensional measurements * Depending on the delivery location, the delivery date may be postponed and additional shipping charge... Read More

The new stainless steel housing has been redesigned and the laser-marked surface is so smooth that there are no places for water droplets to remain after washing. The smooth surface of the housing and the flat back solid mounting surface reduce the incidence of bacteria. All covers can be attache... Read More

This is a typical type of bearing unit, and is equivalent to a combination of a widely used plummer block, an automatically widely used plummer block, and a self-aligning ball bearing. It can be easily tightened by simply tightening it, and is most often used in transmission devices and general m... Read More

Single row deep groove ball bearings are the most typical type of rolling bearings and have a wide range of uses. The orbital grooves provided on the inner and outer rings form a cross section of an arc having a radius slightly larger than the radius of the rolling ball. In addition to radial loa... Read More

The new stainless steel housing has been redesigned and the laser-marked surface is so smooth that there are no places for water droplets to remain after washing. The smooth surface of the housing and the flat back solid mounting surface reduce the incidence of bacteria. All covers can be attache... Read More

A bearing unit that combines a ball bearing for the unit and a bearing box with a square flange. Suitable for mounting on a vertical surface such as the side of a machine. The bearing box is attached to the machine body with four bolts.

The cost per transmission horsepower is low. It is commercially available. Easy to handle.

Since it is designed with a low natural frequency, vibration isolation in the low frequency range is possible. A type in which bolts are integrally molded on the upper and lower surfaces. Vibration isolation for equipment weighing 1.6 to 100 kg with 4-point support. Anti-vibration for pumps, comp... Read More