The reviews are automatic translation.
On 2018-08-28 23:11:59
I used it to connect the copper pipe. There is no problem in particular.
On 2018-06-16 17:37:05
I think that it is very good product and excellent in cost performance.
It is used for an air tank.
On 2018-04-16 18:08:32
Some stores are cheaper than others, and some are expensive.
There are many things with short delivery times, but there are also very long ones.
I use it properly.
Water piping end
On 2018-03-04 18:55:22
It is used for edge cutting of water piping which became unnecessary. I tried using it because it was a difficult place to solder under the floor. Work was easy and it was possible to use without problems.
Hot water piping
On 2018-01-22 16:33:03
Although the ring type is a little expensive, soldering is unnecessary and it was easy to construct.
The connection strength of the ring was also sufficient.
On 2017-12-05 21:05:02
I misunderstood that sleeve (abacus ball) is not attached, but it was properly attached.
Connect to air tank
On 2017-11-14 16:33:48
It is very cheap and it can purchase it and I am very satisfied without air leakage
Kerosene tank piping
On 2017-03-02 20:42:23
The price was also cheap, very easy to use, work progressed smoothly.
On 2016-10-19 17:39:28
It does not specify whether a ring ball is attached or not. Result Although it was attached, it is unkind, it is a shame to wish you can write a bit, so that you can purchase without stress. If the item arrival was also a day late, until the return to the house is an excursion, until the product arrives at the user at work?
Repair of water heater
On 2016-07-26 10:01:11
It was urgent, but the next day, it arrived in the morning, so I got the job done soon.
On 2016-04-15 15:59:47
It was used for check pipe and copper pipe connection. It can be used normally, there is no particular problem.
Oil piping, air piping
On 2015-10-12 18:22:35
It was good if listed pressure resistance etc. (Checked on the maker homepage, it was 3.45 MPa or less)
Water leak test of copper pipe brazed parts
On 2015-05-12 20:39:32
In terms of piping design, the insertion depth of the copper pipe is necessary for precision piping design. The measurement result was 23.4 mm. I also appreciate G (PF) screws on the mounting screws. Although it is in other companies, it is expensive.
Air piping in the garage
On 2015-03-09 11:52:12
I purchased it by mistake in size but it was a mistake order from my misunderstanding. The size table at the time of ordering was easy to see. It is saved because many products with attractive prices are prepared. Thank you for your next opportunity.
Pipe repair accompanied by hot water type ceiling embedded bathroom dryer replacement
On 2015-01-30 20:00:18
Existing bathroom dryer was piped by 8φ copper tube brazing and we tried to repair too because the back of the ceiling was so narrow that we could not braze work so we used this product. There was no leakage and piping could be done without brazing
Piping work of home tank
On 2015-01-19 15:42:37
Although some of the oil leakage was confirmed after installing in the past, it seems that it got better whether there was improvement of the ring.
Connection of existing copper pipe
On 2014-11-14 22:53:05
Is the ring nut size 21 mm? I wish it was a normal spanner size.
Grease piping of blower
On 2012-04-25 12:51:31
It can be used as usual. The refrigerant pipe is used as a grease pipe and it is used as a connecting metal. If you prepare more various hardware, variations will spread and it will be saved.
NC lathe cutting oil joint
On 2010-09-23 22:13:52
Because the six corners are wide, you can strongly fix the pipe!