The reviews are automatic translation.
On 2018-12-16 22:28:49
It was a mistake of selection. It is too soft for tungsten sharpening. It is very fast to reduce.
On 2018-05-21 01:22:56
The product is wonderful.
The problem is packing. It was lacking when it arrived with only one bubble wrap (thin).
The second time was also missing. Although it is not a creamer, I returned it twice.
I endured it because the third time was a little.
However, I am satisfied with Mr. Monotaro's correspondence.
Replacement of consumables
On 2017-12-20 22:06:24
We can not purchase 100 mm size wheels easily at home centers, so we are saved.
It is a scratch on a ball that makes me feel lost because the price is not much different from a wheel of a larger size.
Please develop 100mm grindstone with our own product of monotaro.
We look forward to bargain cheap sale.
On 2017-05-21 20:50:48
I received it immediately very much, but the price was normal.
Carbide knife finish
On 2017-04-10 13:14:45
There is no problem to the product itself, the feeling of use is also good. But packing is disappointing. This time I bought two pieces of GC and WA red, whereas the WA red one was wrapped in cushioning material (bubble wrap), whereas this GC was a plastic with only one thin cardboard on one side. Thanks to this, there was a little dent as small finger nails on the side without cardboard. I will use it as it is because there is no problem on the purpose of this time, but I think that I am returning it for the purpose of severe polishing.
Polishing of metal products
On 2017-02-05 20:47:42
I did not sell it to the home center, and I could purchase it cheaply.
On 2017-01-11 21:34:37
It may be the reason of the double-headed grinder that I own, but it is ubiquitous in the direction perpendicular to the rotation axis.
Polishing of carbide drill blades
On 2017-01-05 22:58:40
With the grinding stone attached to the grinder, the carbide drill blade (monotalou, detailed unknown) was not ground, so it was replaced with a GC grindstone. For GC grinding wheels, the carbide blade can be successfully grounded, but on the contrary, the high-speed blade and the cobalt high-speed blade are excessively ground and can not be finely adjusted (the high-speed blade which is thinner than approximately φ 4 has a contact portion at the time of contact with the grindstone It felt like disappearing).
On 2016-11-17 16:05:07
Especially None None None None in particular
Sharp cutting tool
On 2016-10-25 18:33:46
It can be used without problems. If the price goes a little cheaper ...
Purchase as a grinder stone exchange
On 2016-08-26 16:17:34
I am satisfied that it was immediately delivered at a low price.
On 2016-06-30 16:08:57
No particular problem
On 2016-04-20 21:21:08
There is no particular problem.
On 2016-03-29 15:10:32
I installed it in the tabletop grinder I got. I contacted Monotaro with the mounting hole diameter and I admired the appropriate reply. The impression is neither good nor bad.
Lathe turning tool
On 2016-02-17 09:58:15
In the case of super steel it is a little more.
On 2015-11-28 16:46:10
It is good.
Cemented carbide, cermet byte sharpening
On 2015-10-15 21:00:05
I have not used anything other than Noritake, but I think that it is a good thing that there is not any dissatisfaction with this
On 2015-05-19 21:30:31
It is a pottery shop. I am using it for polishing the bottom of a pendant. It can be cut smoothly. Since there is a thickness, it is appreciated without sacrificing it.
For grinding of cutlery in general
On 2015-04-29 22:04:15
The maximum circumferential speed is about 20% higher than the general item, so you can raise the revolution by that much, so you can grind efficiently.
On 2014-09-30 13:39:17