Customer Reviews of High Speed Steel Drill, "Ultra Musashi Dril"
The reviews are automatic translation.
Showing 1 - 18 of 18 Reviews
Drilling work of PVC pipe VU40
On 2019-05-17 18:45:42
The drill will catch when the hole is pierced and the pipe will be lifted. If you look at it, a burr of about 0.5 mm remains. It will improve if you use it for a while, but it will not cut at the end and it will be difficult to make holes. We purchased Kiri of 6mm and 4mm, but there was no problem in 4mm.
Drilling of aluminum pipe
On 2019-03-01 16:15:05
After processing, the back burr is less and it is saved. Other bits will be gradually replaced with this type.
This review is about item#37005464.
Drilling of aluminum plate
On 2018-11-17 17:14:25
Even without positioning with a punch, it was possible to drill beautifully without deviating from the aimed position.
This review is about item#37006261.
Drilling of aluminum panels
On 2018-09-30 00:38:39
Post-processing is easy because there are few back burrs (not at all). Just about Φ 7.5 mm has the same degree of misalignment as the ordinary drill with a tip of about 5 mm. I think that Mitsubishi's plate pull drill EPSS has less misalignment. On the other hand, in the case of placing a through hole after VUCDSCB for Mitsubishi's violet precision drill spot facing, it is best for the tip to be an ordinary drill shape because the core is not determined in EPSS.
This review is about item#37007031.
Drill holes in the thin plate
On 2018-09-16 01:20:06
The position is difficult to shift. Drilling speed is fast. Bali is reduced and it becomes a beautiful circle. It was a good product.
This review is about item#37006426.
On 2018-07-07 00:17:21
I think that it is good for drilling which I do not want absolutely misalignment. However, the sharpness of the small tip drill part is not so good and takes time.
This review is about item#37006207.
Drilling of a frame of a large-sized vehicle and body processing
On 2018-04-11 19:06:11
I tried to drill a 20 mm iron plate with 12 mm drill. I used a grinding oil spray, but I got a hole beautifully comfortably without having heat. Is it possible with high tension?
This review is about item#37005412.
For plastic processing
On 2018-01-07 16:56:09
With the drill blade up to now I was in trouble because the cutting edge was quite rampant, but this product can not drill a blade and can drill a very beautiful perfect circular hole.
This review is about item#37006557.
t0.5 Drilling of tinplate
On 2017-09-08 13:38:40
Used in drilling machine. Although the position is easy to target, Bali will appear as it is and no real circle will come out. Eventually, deburring also became necessary through reamers.
Drilling to 5 mm thick resin plate
On 2017-02-02 15:05:36
In ordinary drills for iron and steel, when the bit penetrates, it gets caught on the board and the hole can not be opened beautifully, but you can drill precisely without using this bit or casually though the hole can not be opened cleanly. However, since it will be caught if you send it earlier so as to open a hole early, I think that it is a point to send slowly.
This review is about item#37006907.
Drilling of plastics
On 2016-03-01 22:17:29
It was good because drilling at one time is possible
This review is about item#37005823.
To use for drilling on thin plate
On 2015-11-08 18:54:06
The hole can be machined to the thin plate as accurately as possible.
This review is about item#37006532.
I attach a small cut ball to the flat bottom hole, but this drill may be good
On 2015-08-18 17:09:03
It was good that the holes opened and the cut beads were firmly glued as expected.
This review is about item#37006182.
Drilling of plastic
On 2014-10-18 00:16:41
I bought it for drilling of plastic. Although the back burr is also so, the table burr drastically decreases and it is saved very much. The place which can be used also for ironworks is very convenient.
Used for handrail processing
On 2013-11-16 08:18:05
Although it is used for drilling aluminum, it is okay that burrs are not necessarily, but aluminum dregs often can not be removed. Considering the trouble of taking Bali, I think that it is faster to take off the dust.
Drilling of aluminum plate and iron plate.
On 2013-07-25 20:36:58
Aluminum plate 1.5 t, iron plate 1.0 t with general drill and comparing this product under the same condition Almost no superiority or inferiority.
This review is about item#37006182.
Aluminum drilling work
On 2012-12-26 18:35:32
A normal hole where the back burr appears is opened.
This review is about item#37006033.
On 2012-09-01 19:04:40
Purchase for drilling for rivets and bolts, easy to use by opening burr-free holes in the targeted place. I feel that it seems a bit bad.
This review is about item#37006751.
Customers Who Viewed This Item Also Bought
Mitsubishi Hitachi Tool Engineering (former Hitachi Tool Engineering)
32.99 - 43.99 SGD
8.99 - 16.99 SGD
489.90 - 649.90 SGD