Buy more than* S$200* and get FREE SHIPPING
--Note--
Due to the heavy typhoon attacked to Japan on Sep/4/2018,
Items will be shipped from Narita International Airport(NRT) or Chubu Centrair International Airport(NGO),
which normally should have been shipped from Kansai International Airport(KIX).
It may cause delay on shipment. Sorry to have kept you waiting and thank you very much for your understandings.

Permanent Magnetic Holder

Sort by:
Showing 1 - 30 of 95 Results
Show: 30 60 90
VIEW: Grid View List View
Neodymium Magnet Holder
TRUSCO
4.75(4)
11.99 - 18.99 SGD
Caution: Do not screw in to deep. Too deep threadening may make magnet fall out., Do not screw in to deep. Too deep threadening may make magnet fall out., Purpose: To embedding int jig and tool, and adsorption., To embedding int jig and tool, and adsorption., 2014 TRUSCO Published Page: 1-0756, Maximum Temperature (Degree C): 80
Category Permanent Magnetic Holder
Permanent Magnetic Holder
KANETEC
19.99 SGD
ADD TO CART
Caution: T-shaped handle not included, T-shaped handle not included, Purpose: Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Adsorption Strength (N [kgf]): 100[10], Tapped-hole Processing: Available, Screw Holes for Mounting: M6, deep, 8mm, Surface Processing: Coating, Outside Diameter x Height H (phi mm x mm): phi26x25, Weight (g): 80, TRUSCO Part Number: 107-6701
Category Permanent Magnetic Holder
Permanent Magnetic Holder
KANETEC
35.99 SGD
ADD TO CART
Caution: T-shaped handle not included, T-shaped handle not included, Purpose: Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Adsorption Strength (N [kgf]): 200[20], Tapped-hole Processing: Available, Screw Holes for Mounting: M6, 10mm deep, Surface Processing: Coating, Dimensions (Length L x Width W x Height H) (mm): 60x26x25, Outside Dimension (depth D x Width W x Height H) (mm): 26x60x25, Weight (g): 250, TRUSCO Part Number: 107-6728, Others: *T-SHAPED HAND...
Category Permanent Magnetic Holder
Magnet Holder, Round
BeHAUS
4.67(3)
3.99 - 5.99 SGD
Caution: Keep away from clocks and PCs., Keep away from clocks and PCs., Purpose: Can be used as material such as steel plates, molds, jigs, tools, etc., Can be used as material such as steel plates, molds, jigs, tools, etc., Material: Anisotropic ferrite magnet, Accessories: Double sided tape
Category Permanent Magnetic Holder
Permanent Magnetic Holder
KANETEC
50.99 SGD
ADD TO CART
Caution: T-shaped handle not included, T-shaped handle not included, Purpose: Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Adsorption Strength (N [kgf]): 500[50], Tapped-hole Processing: Available, Screw Holes for Mounting: M8 deep 12mm, Surface Processing: Painting coating, Outside Diameter x Height H (phi mm x mm): phi50x40, Weight (g): 500, TRUSCO Part Number: 107-6752
Category Permanent Magnetic Holder
Magnet Holder, With Handle
TRUSCO
3.00(3)
19.99 - 64.99 SGD
Category Permanent Magnetic Holder
Magnet Holder
TRUSCO
3.83(6)
2.99 - 5.99 SGD
Screw Dimensions: M4, Dimension (phi x Height H) (mm): 44x8, Weight (g): 54
Category Permanent Magnetic Holder
Magnet Holder
KANETEC
35.99 SGD
ADD TO CART
Purpose: For weight of diagram, ruler, and paper mold. Can be used by embedding into press die. For hold work while wire cut work., For weight of diagram, ruler, and paper mold. Can be used by embedding into press die. For hold work while wire cut work., Adsorption Strength (N [kgf]): 50[5], Screw Holes for Mounting: None, Surface Processing: Nickel-plated, Outside Diameter x Height H (phi mm x mm): phi18x8, Weight (g): 2.5, Specification: Rare earth samarium and cobalt magnet applied Adsorption power: 20 deg C = 100%, 100 deg C = 95%, 200 deg C = 85% Continuous use should be 150 deg C max. 200 deg C is acceptable only for short time use.
Category Permanent Magnetic Holder
Permanent Magnetic Holder
KANETEC
35.99 SGD
ADD TO CART
Caution: T-shaped handle not included, T-shaped handle not included, Purpose: Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Adsorption Strength (N [kgf]): 300[30], Tapped-hole Processing: Available, Screw Holes for Mounting: M8, 12mm deep, Surface Processing: Coating, Outside Diameter x Height H (phi mm x mm): phi40x30, Weight (g): 240, TRUSCO Part Number: 107-6744
Category Permanent Magnetic Holder
Magnet Holder, Square
BeHAUS
4.00(2)
5.99 - 10.99 SGD
Caution: Keep away from clocks and PCs., Keep away from clocks and PCs., Purpose: Can be used as material such as steel plates, molds, jigs, tools, etc., Can be used as material such as steel plates, molds, jigs, tools, etc., Material: Anisotropic ferrite magnet, Accessories: Double sided tape
Category Permanent Magnetic Holder
For T Type Handle Km-03C
KANETEC
5.00(2)
2.99 SGD
Category Permanent Magnetic Holder
Permanent Magnetic Holder
MonotaRO
5.00(2)
9.99 SGD
Screw Holes for Mounting: Without, Surface Processing: Plating
Category Permanent Magnetic Holder
Permanent Magnetic Holder
KANETEC
23.99 SGD
ADD TO CART
Purpose: Presser for drawing, ruler, forming sheet. Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die. Can be used to hold workpieces during wire cutting., Presser for drawing, ruler, forming sheet. Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die. Can be used to hold workpieces during wire cutting., 2014 TRUSCO Published Page: 1-0758, Adsorption Strength (N [kgf]): 100[10], Tapped-hole Processing: 3.0 to a depth of Y in the pilot hole on the back, Screw Holes for Mounting: None, Surface Processing: Paint, Outside Dimension (depth D x Width W x Height H) (mm): 26x26x25, Weight (g): 110, TRUSCO Part Number: 107-6710, Specification: Ferrite magnets application Given that suction ability is 100% at 20...
Category Permanent Magnetic Holder
Permanent Magnetic Holder
KANETEC
26.99 SGD
ADD TO CART
Caution: T-shaped handle not included, T-shaped handle not included, Purpose: Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Adsorption Strength (N [kgf]): 150[15], Tapped-hole Processing: Available, Screw Holes for Mounting: M6, 8mm deep, Surface Processing: Coating, Outside Diameter x Height H (phi mm x mm): phi30x25, Weight (g): 110, TRUSCO Part Number: 107-6736
Category Permanent Magnetic Holder
Magnet Holder
KANETEC
5.00(1)
18.99 - 55.99 SGD
Category Permanent Magnetic Holder
Alnico Magnet
KANETEC
23.99 - 62.99 SGD
2015 Trusco Published Pages: 1 0810, Mounting Screw: -
Category Permanent Magnetic Holder
Permanent Holder Mag Pad
KANETEC
75.99 - 109.99 SGD
Purpose: A wire electrode of a wire electric discharge machine, to protect from the release of easy cooling liquid to occur at the time of the start of processing, prevent heat generation disconnection due to air discharge equipment. Magupaddo is, the wire electro, 2015 Trusco Published Pages: 1 0811
Category Permanent Magnetic Holder
Heat resistant Clamp Meter
KANETEC
229.99 SGD
ADD TO CART
Purpose: To wiring and fixing of the small-diameter code of thermocouples and high-temperature location. Happy fixed in places where the tape can not be used. It can also be used as a temporary fixture for the tool and welding temperature measurement., 2015 Trusco Published Pages: 1 0811, Adsorption Ability (N): 196, Outside Diameter x Height H (phi mm x mm): 50x67, Weight (kg): 0.5, TRUSCO Part Number: 406-3775
Category Permanent Magnetic Holder
All Catch
TRUSCO
33.99 - 43.99 SGD
Category Permanent Magnetic Holder
Magnetic Hexagonal Holder
TRUSCO
78.99 - 129.99 SGD
Purpose: Temporary joint of welding work., Temporary joint of welding work., 2014 TRUSCO Published Page: 1-0778, Holding Angle (degree): 45,90,135, Material: Magnet: Ferrite magnet Exterior: Steel
Category Permanent Magnetic Holder
Magnet Holder
KANETEC
58.99 SGD
ADD TO CART
Purpose: Welding temporally adhesion for construction, bridge, shipbuilding, pipe fitting etc., Welding temporally adhesion for construction, bridge, shipbuilding, pipe fitting etc., 2014 TRUSCO Published Page: 1-0779, Screw Holes for Mounting: M8x1.25, Dimensions (Width W x Depth D x Height H) (mm): 50x66x44, Adsorption Ability (N): 1000, Weight (g): 750, TRUSCO Part Number: 288-3317, Specification: No ON/OFF function.
Category Permanent Magnetic Holder
Plate catch (Silicon coating)
MAGNA
74.99 SGD
Outer Diameter x Inner Diameter x Thickness (mm): 20x3.5x5, Mass (g/piece): 5, Compatible Screw: M3, Adsorption Ability (N): 11.76
Category Permanent Magnetic Holder
Magnet Holder (Samarium-Cobalt magnet)
TRUSCO
18.99 - 36.99 SGD
Caution: ※ Please pay attention to the depth of the screws. ※ There is a possibility that is out of deeply screwed and magnet., Maximum Temperature (Degree C): 250, 250
Category Permanent Magnetic Holder
Magnet Holder
SHIMONISHI SEISAKUSHO
13.99 - 22.99 SGD
Category Permanent Magnetic Holder
Magnet Holder
SHIMONISHI SEISAKUSHO
0.99 - 3.99 SGD
Category Permanent Magnetic Holder
Heat resistant Magnet Holder
SHIMONISHI SEISAKUSHO
16.99 - 24.99 SGD
Maximum Temperature (degreeC): 250, 250
Category Permanent Magnetic Holder
Permanent Magnet Holder Samarium cobalt magnet Round・Stainless type
KANETEC
33.99 - 63.99 SGD
Purpose: Drawings, ruler, such as the pressing of the paper type. To hold the wire cutting work during the work., 2015 Trusco Published Pages: 1 0809, Mounting Screw: -
Category Permanent Magnetic Holder
Hexagon Permanent magnet holder with plate
KANETEC
27.99 - 33.99 SGD
2015 Trusco Published Pages: 1 0811
Category Permanent Magnetic Holder
Samarium-Cobalt Magnet Holder
TRUSCO
20.99 SGD
ADD TO CART
Outer Diameter (phi mm): 16, Adsorption Ability (N): 61, Weight (g): 11, Height (mm): 8, TRUSCO Part Number: 440-9922
Category Permanent Magnetic Holder
Pocket Magnet Holder
MAGNA
33.99 SGD
ADD TO CART
Depth (mm): 12, Weight (g): 150, Height (mm): 65, Width (mm): 85, TRUSCO Part Number: 449-6990
Category Permanent Magnetic Holder

1 2 3 4 Next