Buy more than* S$200* and get FREE SHIPPING
--Note--
Due to the heavy typhoon attacked to Japan on Sep/4/2018,
Items will be shipped from Narita International Airport(NRT) or Chubu Centrair International Airport(NGO),
which normally should have been shipped from Kansai International Airport(KIX).
It may cause delay on shipment. Sorry to have kept you waiting and thank you very much for your understandings.

Brace Joint Hardware

Sort by:
Showing 1 - 18 of 18 Results
Show: 30 60 90
VIEW: Grid View List View
Joint Tool, Hole Down Corner 10kN
TANAKA
5.00(1)
6.99 SGD
ADD TO CART
Short Standard Joint Strength (kN): (Corner of mast-)12.4, Performance Certified: S10A02-06, HOUSEPLUS Resident Warranty: HP08-KT031, Notice No.1460 No.2: To, N Value: 2.5 or less, Short Allowable Tensile Strength (kN): (In the mast-)13.5, Surface Processing: Alloy coated steel sheets, Thickness (mm): 2.3, Material: NSDHC/ZYXK18, Accessories: Special (NO. 3) ANGLE OF bit screw (TBA-65D) x 6 BOOK, Application: Used to connect pillar and horizontal beam
Category Brace Joint Hardware
Hyper Gusset II
BX Kaneshin
5.00(2)
3.99 SGD
ADD TO CART
Surface Processing: Hot-dip galvanized steel sheet (Z27), Standard: Houseplus Residential Security Corporation Performance Test HP06-KT120, HP06-KT121, HP06-KT066, HP06-KT067, Material: JIS G 3302 SGH340, Accessories: (No. 3) Rectangular-head screw CPQ-45(Gray) x 14 pieces, Application: It is the hardware which joins easily and firmly braces for wall magnification (90-105x45).
Category Brace Joint Hardware
Double Diagonal Brace Bracket
TANAKA
5.00(3)
4.99 SGD
ADD TO CART
Surface Processing: Hot-dip galvanized steel sheet (Z27), Standard: Japan Housing and Wood Technology Center Foundation Mark Z hardware (BP-2) equivalent certificatied, Thickness (mm): 2.3, Material: JIS G 3302(Hot-dip galvanized steel sheet and steel strip)SGHC or SGCC, Accessories: Exclusive (No. 3) bit angle screws (TB-45)x15 pcs, Application: For joining brace of 45mm x 90mm (2 times magnification wall) to pole and beam
Category Brace Joint Hardware
Double Diagonal Brace
TANAKA
5.00(4)
3.99 SGD
ADD TO CART
Surface Processing: Hot-dip galvanized steel sheet (Z27), Standard: Japan Housing and Wood Technology Center Foundation Mark Z hardware (BP-2) equivalent certificatied, Thickness (mm): 2.3, Material: JIS G 3302(Hot-dip galvanized steel sheet and steel strip)SGHC or SGCC, Caution: Outdoor only. Please wear gloves, etc. in order to prevent injury., Accessories: Exclusive (No. 3) bit angle screws (TB-45)x15 pcs, Application: For joining brace of 45mm x 90mm (2 times magnification wall) to pole and beam
Category Brace Joint Hardware
Pillar Construction Braced Hardware III
BX Kaneshin
3.99 SGD
ADD TO CART
Standard: Inspection houseplus Corporation performance testing HP08-KT075/HP08-KT082, (GOODS) 2435 NO. 08 A BUILDING MATERIALS TEST CENTER QUALITY PERFORMANCE TRIAL REPORT FOR 08 A / 2434 NO., Material: ZAM * (MSM-HC-D90 OR MSM-CC-DA90), Caution: Please always join with installation screws Square bit(# 3) for screw junction is sold separately. Install the necessary hardware to pedestal and capital joints., Accessories: PILLAR SIDE ONLY (NUMBER 3) SQUARE SCREW CPQ-75 (BLUE) x 6 BOOKS, BRACING SIDE ONLY (NUMBER 3) SQUARE SCREW CPQ-45 (GREY) X 6, Application: It is the hardware which joins easily and firmly braces for wall magnification (90-105x45).
Category Brace Joint Hardware
Flat Bracket
BX Kaneshin
3.00(1)
3.99 SGD
ADD TO CART
Caution: Screw joints for squareuare bits (# 3) is not included. Install the hardware necessary to the body column base and column head joints.For the brace , please be sure to use 7 joining screws, Purpose: It is the hardware which joins easily and firmly braces for wall magnification (90-105x45)., Laws and Regulations: Daira 12 public notice No. 1460 advice no. 1 (to), Plate Thickness (mm): 0.6, Standard: (GOODS) 2435 NO. 06 A BUILDING MATERIALS TEST CENTER QUALITY PERFORMANCE TRIAL REPORT FOR 08 A / 2331 NO., Material: NSS431DP-2 (high intensity diplophase stainless steel), Accessories: (No. 45) Rectangular-head screw CPQ-15(Gray) x 6 pcs.
Category Brace Joint Hardware
Countersunk Screw Diagonal Brace Box II
KANAI
5.99 SGD
ADD TO CART
Caution: Screws should be striked; 4pcs on column, 4pcs on horizontal member, 7pcs on diagonal brace. Use attached screws., Laws and Regulations: Corresponding to (d) 1, No. 1460 No. 1 Section Ministry of Land, Infrastructure and Transport Notification, Plate Thickness (mm): 2.3, Surface Processing: De to yuraru Court, Standard: No. No. 03A2113 (Foundation) Testing Center for Construction Materials accepted, Material: SPHC (JIS G3131), Accessories: YA-S45x15 Movies
Category Brace Joint Hardware
Hex Plate Bracket SD
TANAKA
5.00(2)
4.99 SGD
ADD TO CART
Caution: For tightening dedicated angle bit screw TBA-45, please use the (optional) third square bit., Purpose: For joining the end of the braces of 90mm x 90mm (3 times magnification wall) and braces of 45mm x 90mm (Double wall magnification), Proof Strength Test: 45 x 90 mm brace joints: per 1 m of goods and Japan housing & wood technology center performance certified bracing walls allowed 3.23 kN shear _ 000 D x _ 45 x 90 mm brace joints: per 1 m of goods and Japan housing & wood technology center performance certified bracing walls allowed 3.23 kN shear _ 000 D x _, Laws and Regulations: Notice No. 1460 No. 1(Ni and Ho), Surface Processing: Zn-11% Al-3% Mg-0.25 Si alloy coated steel sheet (superdyma), Dimension (mm): 170x170, Thickness (mm): 0.6, Material: NSDC 570: ZYXK18 (NEW JAPAN I...
Category Brace Joint Hardware
N- Freedom Diagonal Brace Plate, for Wall Magnification x2
KANAI
3.99 SGD
ADD TO CART
Laws and Regulations: The land, infrastructure and transportation notification No. 1460 (1) No.1 (2)., Surface Processing: Black galvanization, Standard: (INSTITUTES) (GOODS) # 06 A 1259 NO. 06 A 1,260-CENTER FOR CONSTRUCTION MATERIALS (STANDARD SPECIFICATION) (GOODS) BUILDING MATERIALS TEST CENTER (FLOOR PLYWOOD SPECIFICATIONS) AND HOUSEPLUS RESIDENTIAL WARRANTY CO., LTD. HP06-KT051 (IN YOUR SPECIFICATIONS), Material: NFG550F, Caution: Adjust height of mounting metal parts on the place that you surely can put 6 screws on diagonal brace side Please note if screw comes off from diagonal brace, it can't maintain required strength. There are guide points which makes determining the in, Accessories: 3-SQUARE SCREW (45 X 13 YS-N), Application: Metal fitting for diagonal brace (45 x 90 mm). For ...
Category Brace Joint Hardware
Freedom 45 Plate
KANAI
5.00(1)
4.99 SGD
ADD TO CART
Surface Processing: Z27, Standard: Land traffic Ministry of public notice No. 1460 No. (1) No. 1 table 3 (d) to appropriate, Material: JIS/G3302 SGHC, Caution: Install the hardware at the position 7 screws of diagonal brace side can be tightened surely. Screw strength may get weaken if it comes off diagonal brace side. Please tighten with joint screw attached., Accessories: 3-SQUARE SCREW (45 x 7 BOOK YD-N, 60 X 8 YD-N), Application: Can connect edge part of diagonal brace. Can be installed without bracket bulge out from outside wall
Category Brace Joint Hardware
Double Diagonal Brace LIBERO II
TANAKA
4.33(6)
3.99 SGD
ADD TO CART
Surface Processing: Hot-dip galvanized steel sheet (Z27), Thickness (mm): 2.3, Material: JIS G 3302(Hot-dip galvanized steel sheet and steel strip)SGHC or SGCC, Caution: Please wear gloves, etc. in order to prevent injury., Accessories: Exclusive (No. 3) bit angle screws (TB-45)x14 pcs, Application: For joining brace of 45mm x 90mm (2 times magnification wall) to pole
Category Brace Joint Hardware
Gusset Right
BX Kaneshin
4.50(2)
2.99 SGD
ADD TO CART
Standard: Foundation building materials test center-quality performance test reports _ # 06 A HOBBY FOR # 06 A NO. 2333 / 2332, Material: JIS G 3302 SGH340, Caution: Please always join with installation screws Square bit(# 3) for screw junction is sold separately. Be sure to join 7 screws on each diagonal brace. Install the necessary hardware to pedestal and capital joints., Accessories: -COLUMN (HORIZONAL) FOUNDATION (NO. 3)-SIDE-ONLY SQUARE SCREW CPQ-45 (GREY) X 8 BOOKS, PRIVATE SIDE BRACE (NO. 3) SQUARE SCREW CPQ-30 (SILVER) X SEVEN, Application: It is the hardware which joins easily and firmly braces for wall ratio is 2times (90-105x45) or brace which wall.ratio is 1.5times(90-105x30)
Category Brace Joint Hardware
Gusset Bracket
BX Kaneshin
3.99 SGD
ADD TO CART
Caution: Pay attention for mounting height of main body. Use dedicated screw packed in this product. Use materials required for capital and pedestal (not included). Better to use bit more 125mm or more., Purpose: It is the hardware which joins easily and firmly braces for wall magnification (90-105x45)., Laws and Regulations: First, No. 1460 No. 12 KenTsuge notice flat (c), Surface Processing: Hot-dip galvanized steel sheet (Z27) , Standard: HP06-KT119 / HP06-KT061 / HP06-KT062 / HP06-KT063 (stock) performance test house plus confirmatory test , Material: JIS G 3302 SGH340, Accessories: (CPQ-45) (gray) x9 this pillar side dedicated screw, (CPQ-30) (Silver) x5 this bracing side dedicated screw
Category Brace Joint Hardware
Termination Plate
KANAI
4.99 SGD
ADD TO CART
Caution: Use 15 screws in total. For diagonal brace 7 places (select from 9 places), 4 places on column, 4 places on horizontal member.Make sure to use connection screw installed., Laws and Regulations: Corresponding to (d) 1, No. 1460 No. 1 Section Ministry of Land, Infrastructure and Transport Notification, Plate Thickness (mm): 0.7, Surface Processing: 2B material (cloth) , Standard: No. No. 03A1360 (Foundation) Testing Center for Construction Materials accepted , Material: SUS430 (JIS G4305), Accessories: YA-S45x15 this
Category Brace Joint Hardware
2 times brush Libero II ECO
TANAKA
7.99 SGD
ADD TO CART
Dimension (mm): 47.3x105x102.3x2.3(t)
Category Brace Joint Hardware
Galvanizing Angle Connection
KANAI
4.99 SGD
ADD TO CART
Caution: Install the hardware at the position 6 screws of diagonal brace side can be tightened surely. Screw strength may get weaken if it comes off diagonal brace side. Please tighten with joint screw attached., Laws and Regulations: Corresponding to (e) 1, No. 1460 No. 1 Section Ministry of Land, Infrastructure and Transport Notification, Plate Thickness (mm): 1.6, Surface Processing: Galvanizing , Standard: House plus home warranty (stock) HP06-KT032 (standard specification) House plus home warranty (stock) HP06-KT033 (plywood floor specification) , Material: NFG550F, Accessories: (phi6.0x43) x6 this• (YS-N60) x6 this pot screw
Category Brace Joint Hardware
1.5 Times Diagonal Brace LIBERO
TANAKA
5.00(1)
4.99 SGD
ADD TO CART
Caution: For tightening dedicated angle bit screw TBA-65D and TBA-30 , please use the (optional) third squareuare bit., Purpose: For joining the end brace of 45mm x 90mm (1.5 times magnification wall), Proof Strength Test: Bracing walls 1 m per standard 2.0 kN shear, Laws and Regulations: Notice No. 1460 No. 1(Ni and Ho), Surface Processing: Hot-dip galvanized steel sheet (Z27), Standard: HOBBY GOODS AND BUILDING MATERIALS TEST CENTER PERFORMANCE TESTING, #06 A 0232, Dimension (mm): 32.3x120x97.3, Thickness (mm): 2.3, Material: JIS G 3302(Hot-dip galvanized steel sheet and steel strip)SGHC or SGCC, Accessories: (NO. 3) ONLY ANGLE bit screw(TB-30) x 5 /(TBA-65D) x 5
Category Brace Joint Hardware
N- Freedom bracing plate wall magnification 1.5 times for
KANAI
3.99 SGD
ADD TO CART
Caution: This product is manufactured in Japanese standards. Please check the specification before you order., Plate Thickness (mm): 1.6, Material: NFG550F
Category Brace Joint Hardware

1